







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Lomita, CA: What It Costs and What’s Involved
Metal roofing in Lomita typically runs $15,000 to $40,000 for a full installation, and most homes here are done in three to six working days once materials land on site. That range covers standing seam and exposed-fastener systems on a typical 1,200 – 1,800 sq ft bungalow on a 5,000 – 6,000 sq ft lot. Call (888) 345-8164 and we’ll walk your roofline on site and give you a written line-item quote.
How a Metal Roof Goes On, Stage by Stage

Metal roofing is a sequenced job, not a one-day swap. Here’s what actually happens, and where you’ll be asked to make a call.
Stage 1: Tear-off and deck inspection (day 1)
We strip the existing shingles, tile, or old metal down to the sheathing, then walk the deck board by board. On Lomita’s 1920s – 1950s wood-frame homes, soft or split boards are common. You decide whether to overlay new sheathing or replace only the failed sections. Budget a day, sometimes a day and a half if the original deck is rough.
Stage 2: Structural and flashing prep (day 2)
Metal weighs less than tile but still needs solid fastening points. We check rafter spacing, add purlins where the panel profile requires them, and set the underlayment. Penetrations, valleys, and the wall-to-roof junctions get flashing detailed before a single panel goes up. This is the stage that decides whether the roof lasts, and you don’t see it once the panels are on.
Stage 3: Panel layout and installation (days 3 – 4)
You’ll have already chosen panel type, color, and finish. We lay out panels to minimize seams and waste, which on small, tight infill lots means measuring twice. Standing seam panels are rolled to length and run full slope. Exposed-fastener panels go down faster and cost less. Either way, panels are screwed or seamed per manufacturer spec.
Stage 4: Trim, ridge, and detail work (day 5)
Ridge cap, gable trim, drip edge, and any vent flashing get installed. We also seal and finish all penetrations. This is where a cheap job shows, and where a good one pays off for the next 40 years. You’ll want to look at the finished trim lines before signing off.
Stage 5: Inspection and walkthrough (day 5 or 6)
We pull the City of Lomita permit before work starts, so the final sign-off is scheduled with the local inspector. Then we do a walkthrough with you, clean the site, and hand off the manufacturer warranty packet and our 730-Day Done Right Promise paperwork in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Metal roofing is not one product. Here’s what Lomita homeowners actually pick between, with honest trade-offs.
- Standing seam (the premium pick): Hidden fasteners, clean vertical lines, no exposed screws to back out over time. Runs $18,000 – $40,000 on a typical Lomita roof. Best choice for salt air since there are fewer penetration points to corrode. Worth the upcharge on homes that will stay in the family.
- Exposed-fastener panels (the value pick): Screwed through the face with washers. Cheaper at the low end of the range, around $15,000 – $25,000. The trade-off: washers and screws need inspection every few years, and in Lomita’s salt air, that faster corrodes. We specify coated fasteners to slow it down.
- Galvalume steel vs. aluminum: Steel with a metallic coating is the standard. Aluminum costs more but hangs tougher near the coast. On the small lots off Pacific Coast Highway, where marine layer sits longer, aluminum is often the smarter long play. We’ll walk you through the cost difference in the estimate.
- Stone-coated steel (the “tile look”): Stamped to mimic barrel tile or shake. A popular pick where an HOA or neighbor expects a traditional profile. Runs in the middle of the range. Heavier and costs more than plain exposed-fastener, but hides salt stains better on a light-colored finish.
- Color and finish: Kynar-based coatings hold color longest in salt air. Light colors reflect the summer heat. Darker tones look sharper but show chalk and salt more. Choose the finish you want to look at for 30 years.
What Metal Roofing Costs in Lomita, CA

Most Lomita metal roof installations land between $15,000 and $40,000. The low end is a modest single-story bungalow with a simple gable and exposed-fastener panels. The high end is a larger or more complex roof with standing seam, aluminum panels, and structural repair underneath.
What moves the number:
- Roof size and pitch: Every extra square of area and every steep section adds labor. A steep second story over a low-slope porch is more work than a simple ranch.
- Existing roof condition: If the deck has rot, or there are layers of old roofing to strip, that’s added tear-off and sheathing cost.
- Panel type: Standing seam over exposed-fastener is the single biggest jump in the range, often $4,000 – $8,000 on a standard Lomita roof.
- Penetrations and complexity: Skylights, chimneys, valleys, and dormers extend the install by a day or more and add flashing cost.
- Permit scope: A straightforward re-roof permit is one thing; structural reinforcement or a tear-down-and-rebuild scope pulls the City of Lomita’s plan-check into the picture, which adds time.
A written estimate from us includes tear-off, underlayment, panels, fasteners, flashing, trim, permit pulling, final inspection, and the 730-Day Done Right Promise. It does not include structural repair discovered under the deck, which we quote separately before doing it so there are no surprise change orders.
See the difference
Before
After
Before
After
Before
AfterWhat Lomita Homes Do to This Job
Lomita is a small, fully built-out Harbor Gateway city, and that changes the trade. Most of what we do here is re-roofing on 1920s – 1950s bungalows and mid-century stucco homes on lots that are 5,000 – 6,000 sq ft. There’s no new subdivision work; there’s tear-off, deck repair, and trim work, done on tight lots. Permits run through the City of Lomita’s own building department, layered on top of LA County’s coastal-area rules, so plan check can take longer than it would in sprawling neighboring Torrance.
The bigger factor for metal is salt air. Marine layer and salt-laden air corrode fasteners, flashing, and older exposed-fastener screws faster than you’d see inland. On homes along Lomita Boulevard and Pacific Coast Highway, we spec coated or stainless fasteners and aluminum panels where the budget allows. We check for it in every estimate: fastener corrosion on the existing roof, stucco cracking at wall junctions, and failed flashing at chimneys. Homeowners often pair a metal roof with Window Replacement in Lomita or Impact Windows & Doors in Lomita to lock down the whole envelope at once. It’s part of a full Roofing in Lomita scope for some homes, but if you just need metal, we stay narrow.
Serving Lomita, CA – Our Local Coverage Area
We serve Lomita and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Lomita

Most Lomita metal roofs are installed in three to six working days once materials are on site, with the permit and inspection scheduling adding a week or more before work starts. If the deck needs structural repair, add two to four days. Call (888) 345-8164 for a timeline based on your specific roof.
Yes. A metal roof installation requires a permit from the City of Lomita building department, and most installations require a final inspection. We pull the permit for you and schedule the inspection as part of the job, so you’re not chasing paperwork. Call (888) 345-8164 to talk through your permit scope.
Yes, in the long run. Standing seam metal with coated or stainless fasteners holds up far better than asphalt shingles against Lomita’s salt air and marine layer. Expect to inspect fasteners and flashing every three to five years, and to re-coat or replace washers before they fail. Call (888) 345-8164 for a corrosion walkthrough.
Every metal roof we install is covered by our 730-Day Done Right Promise, and the manufacturer’s panel and finish warranty flows through to you in writing. If something goes wrong in the two years after install, we make it right. Call (888) 345-8164 to review the specific terms.
Yes, in almost every case. Metal roofing is a roof-only scope. We don’t touch interior plumbing, electrical, or walls unless the deck underneath is failing and needs structural repair, which we quote separately before touching anything. Call (888) 345-8164 for a free on-site estimate.
Get a Metal Roofing Estimate in Lomita
Metal roofing in Lomita runs $15,000 – $40,000, and the right number comes from standing on your roof, not a phone quote. Call (888) 345-8164 and we’ll schedule a free on-site estimate. We pull the City of Lomita permit, pull the final inspection, and back the whole job with our 730-Day Done Right Promise. Upfront pricing, no surprises, written line-item quote in hand. Live person, 24/7.
Written by the team at Groundwork Construction Co.












