







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Lomita, CA: What It Costs and How Fast You Get One
An iron fence on a typical Lomita lot runs $3,500 – $9,000 installed, and most residential jobs finish in 2 – 4 working days once the fence package is set. That range covers a standard front or side-yard run on a 5,000 – 6,000 sq ft lot in the 90717 ZIP, including posts, concrete footings, and finish. Longer street-facing runs, custom scrollwork, or a matching gate push you toward the top of the range. Call (888) 345-8164 for a free on-site estimate and a written line-item quote.
How an Iron Fence Goes In, Stage by Stage

We don’t sell iron fences off a brochure. Every job follows the same sequence, and you know what’s happening on each day.
Stage 1: On-site measure and layout (day 1, about 90 minutes)
We walk the property line with you, confirm exactly where the fence sits relative to the setback, and check what’s underground before anyone digs. In Lomita’s older bungalow stock, that means locating old irrigation lines, gas stub-outs, and the occasional forgotten concrete footing from a previous fence. You decide the fence height and the gate positions on this visit. Nothing gets ordered until you’ve signed off on the layout.
Stage 2: Permit and HOA check (2 – 10 business days, varies)
Most Lomita front-yard fences under 6 feet don’t need a building permit, but corner lots, fences over 6 feet, and anything in the front setback can trigger a plan check with the City of Lomita’s building department. If your property sits in an HOA, we get the architectural approval packet in front of the board before we order material. You’ll know within a few days whether your job is a no-permit job or a plan-check job.
Stage 3: Demolition and prep (half a day to a full day)
Old fence comes out, posts get pulled, and the line gets cleared. On tight infill lots around the Pacific Coast Highway and Lomita Boulevard corridors, access is the constraint: side yards are often 3 – 4 feet wide, so we hand-carry material rather than trying to back a truck in. That adds time on some properties. You decide whether we haul the old fence away or leave it stacked for your own disposal.
Stage 4: Footings and post setting (day 2, roughly 6 – 8 hours)
Posts go in at 6 – 8 foot spacing, set in concrete footings sized to the post and to the local soil. We set posts plumb and brace them, then let the concrete cure before any panels go on. On a standard 100-linear-foot run, we’re typically setting 14 – 16 posts in a day. You don’t need to be home for this stage.
Stage 5: Panels, gates, and finish (day 3 – 4, 1 – 2 days)
Panels get hung, gates get aligned and swing-tested, and any powder-coat touch-up happens last. We walk the fence with you, demonstrate the gate latches, and hand over the finish care sheet. On painted iron, we schedule a touch-up visit 12 months out to catch rust bloom before it spreads.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Iron fence covers a wider span than most homeowners realize. Here’s the honest trade-off on each choice you’ll make:
- Wrought iron vs. steel: Traditional wrought iron carries the look most buyers want, but it’s heavier, costlier, and slower to install. Steel is the practical workhorse in Lomita, and modern steel ornamental fence with a powder-coat finish holds up well against the local salt air at roughly 20 – 30% less than true wrought iron.
- Powder-coat vs. paint finish: Powder-coat is baked on at the factory and lasts 8 – 12 years in coastal conditions before it needs touch-up; field-painted iron needs recoating every 3 – 5 years. On a Lomita property, powder-coat is almost always the better call.
- Picket spacing and height: 4-foot residential fence is the most common front-yard choice; 5-foot is common for side and rear runs. Picket spacing (typically 4 inches for standard, tighter for pet containment) affects the look and the labor.
- Galvanized core vs. standard core: Galvanized steel underneath the finish roughly doubles the corrosion resistance, which matters in this marine-layer environment. It adds 10 – 20% to material cost and is worth it on any fence within a mile of the coast.
- Matching gate: A standard walk gate with a self-closing hinge runs a modest add-on; a double driveway gate with automation is a different project entirely and needs its own estimate.
- Finial and scroll detail: Spear-top finials, scrollwork panels, and custom rails are the “design” choices. They drive visual character and, honestly, they drive cost. Budget accordingly and buy the detail where it’s visible from the street, not on the back fence line nobody sees.
What Iron Fence Costs in Lomita, CA

The working range on a residential iron fence in Lomita is $3,500 – $9,000 installed. Where you land in that range depends on five variables we evaluate on the first visit.
| Factor | Low End ($3,500) | High End ($9,000) |
|---|---|---|
| Linear feet | 40 – 60 ft | 120 – 150 ft |
| Fence height | 4 ft | 5 – 6 ft |
| Material style | Standard steel, powder-coat | Galvanized core, wrought iron, custom scroll |
| Gates | None or one walk gate | Multiple gates or a double drive gate |
| Site conditions | Flat, clean, easy access | Slope, old footings to remove, tight side-yard access |
What’s included in every written estimate: material, powder-coat or paint finish, posts, concrete footings, installation labor, gate hardware, and cleanup/haul-away. What typically isn’t included and gets flagged separately: permit fees if the job requires plan check, HOA application fees, repair of existing concrete in the fence line, and any landscaping that has to come out and go back in.
A note on the market: the Atlas and Tamko material lineup is what we specify most often in this trade, and both have held pricing steady enough that we can quote a firm number on the first visit rather than a “TBD pending material” placeholder. That’s the upfront-pricing, no-surprises standard we hold ourselves to here.
See the difference
Before
After
Before
After
Before
AfterWhat Lomita Homes Specifically Do to an Iron Fence Job
Lomita is a roughly one-square-mile Harbor Gateway city, incorporated in 1964 and completely surrounded by Torrance. There’s essentially no undeveloped land here, so iron fence work almost always runs on tight infill lots against 1920s – 1950s bungalows and early tract homes on 5,000 – 6,000 sq ft parcels. That changes the job two ways. First, side-yard access is the real constraint on almost every install; we plan the material delivery around it rather than discovering it on day 2. Second, the City of Lomita’s own building department handles plan check locally, so whether a fence needs a permit is not the same answer you’d get a city away. Fences over 6 feet, corner-lot fences, and anything in the front setback are the ones that most often get pushed into plan check.
The climate does its own work on the material. Salt air and morning marine layer drive finish failures faster here than they do five miles inland, and we see the same pattern every couple of years: powder-coat flaking at the weld joints on fences that were finished cheaply, followed by rust bloom that spreads along the picket line. That’s why we spec galvanized cores and factory powder-coat on almost every Lomita job. As a broader scope note, if your iron fence is part of a full property update, our Fence Installation in Lomita page covers the wider project. Homeowners often pair this with Patios, Walkways & Pool Decks in Lomita when the front yard is getting reworked at the same time.
Serving Lomita, CA – Our Local Coverage Area
We serve Lomita and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Lomita

Most residential jobs take 2 – 4 working days from demo to final walk-through, plus the permit waiting period if your job requires plan check. The installation itself is compressed; the variable is the permit. A 60-foot front-yard run on a clean lot is often a single-day install plus a follow-up day for posts and cure. Call (888) 345-8164 and we’ll give you a real timeline on your property, not a range.
Most fences 6 feet and under in the rear or side yard don’t require a building permit in Lomita, but corner lots, over-height fences, and any fence in the front setback can trip plan check with the City of Lomita building department. Because Lomita runs its own plan check rather than leaning on LA County, the answer here isn’t the same as it is in neighboring Torrance. We confirm this for your specific lot before ordering material. Call (888) 345-8164 to get a straight answer.
In most cases, yes. Iron fence installation is a surface-and-footing job that doesn’t require plumbing, electrical, or structural work, and it doesn’t disturb the house. The exceptions are old footings from a prior fence, an irrigation line through the fence line, or a gas stub-out in the way. We locate those on day 1 so there are no surprises when the auger starts. If your yard project expands into something structural such as an ADU Design & Permitting in Lomita, that’s a separate scope and gets its own conversation.
Installed cost in Lomita typically runs $55 – $95 per linear foot for standard steel ornamental fence, and $110 – $160 per linear foot for true wrought iron with heavier pickets and custom detail. The full job on a typical Lomita lot lands in the $3,500 – $9,000 range, which is the number most homeowners should anchor on. Gates, custom scrollwork, and difficult access push the per-foot cost up. Call (888) 345-8164 for an exact written quote on your line.
Every iron fence we install is covered by the 730-Day Done Right Promise: if it isn’t done right, we make it right, for two full years. That covers workmanship, footing failure, alignment issues, and gate hardware defects. The powder-coat or paint finish carries its own manufacturer warranty on top, and we’ll provide that in writing. As a general note, our Fence Installation service is backed by the same promise on every job. For properties inside our full Lomita service area, that coverage applies the same way.
Get a Free Iron Fence Estimate in Lomita
Call (888) 345-8164 to schedule a free on-site estimate for iron fence work on your Lomita property. On the call we’ll set a visit window, confirm what you’re trying to accomplish on the lot, and send a written line-item quote after the walk-through. No pressure, no vague numbers, and the price in the quote is the price on the invoice. You get a real timeline, a real material spec, and a 730-Day Done Right Promise behind the work.
Written by the team at Groundwork Construction Co.












