







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Long Beach, CA: What It Costs and How Long It Takes
Metal roofing in Long Beach typically runs $15,000 to $40,000 for a full residential installation, and a standard single-family roof takes 3 to 6 working days from tear-off to final inspection. The range is wide because a 1930s bungalow in Rose Park with three gables and a rear addition prices very differently from a simple hip roof on an east-side tract home. Call (888) 345-8164 for a free on-site estimate with a written line-item quote.
How a Metal Roof Goes On: The Stage-by-Stage Sequence

Most homeowners have never watched a metal roof go on and don’t know what they’re paying for. Here’s the real sequence, with the decisions that land on you at each stage.
Stage 1: Tear-off and deck inspection (day 1 to 2)
We strip the existing roofing down to the sheathing. On Long Beach homes built before 1950, that’s usually skip sheathing: spaced 1×4 boards rather than solid plywood. Spaced boards are common on the older bungalows and fourplexes here, and they need to be overlaid with solid decking before any metal panel or underlayment goes down. If we find rot at the eaves or around chimneys from the marine air, that gets replaced and you approve the change in writing before we continue. No surprise line items.
Stage 2: Deck prep, underlayment, and ice-and-water detailing (day 2 to 3)
New solid decking goes down, then a high-temperature synthetic underlayment and a peel-and-stick membrane at the valleys, penetrations, and eaves. This layer matters more in coastal Long Beach than most homeowners realize; salt air and fog-driven moisture work on everything underneath a roof, and a good underlayment is the second line of defense. Your decision here is underlayment grade if your quote offers a choice.
Stage 3: Panel layout and install (day 3 to 5)
Panels go up in sequence from the eave, screwed or clipped to the deck with fasteners rated for coastal conditions. On a standing seam system the panels are concealed-fastened; on an exposed-fastener panel they’re screwed through. The homeowner decision at this stage is panel type and color, which we lock in before ordering, because lead times vary by manufacturer and finish. Atlas and Tamko both offer panels we install regularly.
Stage 4: Trim, ridge, and flashing (day 5)
Ridge caps, gable trim, drip edge, and all penetrations get finished. Chimneys, skylights, and vent stacks get flashed properly. This is where sloppy work shows up years later as a leak, so we photograph each detail before it’s covered.
Stage 5: Final inspection and walkthrough (day 6)
We do a magnet sweep of gutters and yard, confirm the flashing and fasteners, and walk the roof with you. Your decision here is whether to keep or replace gutters while we’re up there. If your home also needs window upgrades, that’s a conversation to have now, not two months later, and homeowners often pair a roof with Window Replacement in Long Beach while the scaffolding’s already up.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Metal roofing is not one product. The panels differ widely in cost, appearance, and how they hold up against salt air and Santa Ana winds. Here’s the honest breakdown.
- Standing seam panels (concealed fastener). The premium choice. No exposed screws, cleaner lines, longest lifespan. Pricier upfront and the install demands more skill; suitable for homeowners planning to stay 15-plus years or who care about appearance from the street.
- Exposed-fastener panels (screw-down). Lower cost, faster install, and available in a range of colors. The trade-off is exposed washers; in coastal conditions those washers eventually need attention, so this suits budget-conscious jobs and outbuildings more than a forever roof.
- Stone-coated steel. Steel panels coated with stone granules that mimic tile or shake. This one lands well with homeowners who love the Spanish Colonial Revival look typical of the older Long Beach stock but want the weight and cost savings of steel. Boral makes a stone-coated product line we work with.
- Panel gauge and finish. 26-gauge panels hold up better than 29-gauge; a painted finish rated for coastal exposure is worth the upgrade near the water. This is the single variable most homeowners underthink.
- Color and profile come down to HOA approval and taste. In Long Beach, if you’re in a historic-district-adjacent block, the color can be a design-review question, not just a preference.
What Metal Roofing Costs in Long Beach, CA

Expect $15,000 to $40,000 installed, and know that the number is driven by five real variables rather than vague “pricing varies.” A written estimate from us breaks this out line by line. For context, a straight asphalt Roofing in Long Beach replacement sits at $8,000 to $20,000; metal is the upgrade tier and priced accordingly.
- Roof size and complexity. Square footage drives material cost; gables, valleys, dormers, and multiple roof planes drive labor. A simple hip roof prices at the low end, a cut-up 1930s bungalow roof at the high end.
- Deck condition. Skip sheathing on old bungalows needs overlaid solid decking, an extra line item. Rot repair adds more.
- Material grade. Exposed-fastener economy panels land near $15,000-$20,000 on a typical home; standing seam pushes toward $30,000-$40,000. Stone-coated steel sits in between.
- Permit and inspection scope. Coastal Zone review and historic context can add administrative time and fee. We pull the permits and see the inspections through.
- Penetrations and tie-ins. Skylights, chimneys, solar mounts, and vent stacks all mean flashing work. A roof with none of these prices lower.
What’s typically included in our written estimate: tear-off, decking, underlayment, panels, trim, flashing, permits, and cleanup. What’s often not included unless scoped: gutters, skylight replacement, and structural repairs if a rafter is compromised. The 730-Day Done Right Promise backs the workmanship either way, and there’s $1,000 off projects over $10,000 plus 0% financing for 18 months.
See the difference
Before
After
Before
After
Before
AfterWhat Long Beach Homes Specifically Do to This Metal Roofing Job
Long Beach is a hard city to roof because it stacks very old housing on very new regulation. A 1920s Craftsman fourplex in Belmont Heights and a 1930s bungalow in Rose Park sit in a Coastal Zone and a designated historic context, so a metal re-roof can trigger Coastal Commission review, historic design review, and seismic retrofit rules on the same modest lot. That’s a permitting stack you won’t hit on a 1950s east-side tract home or in Carson or Compton, and it’s the single biggest reason a Long Beach metal roof quotes higher than the same square footage inland.
Then there’s the housing itself. The older Spanish Colonial Revival and Craftsman stock, plus the dense 1950s-70s stucco fourplexes, tends to have original skip sheathing and, often enough, un-permitted additions built decades ago. We uncover both regularly. The marine layer and salt air off the Port of Long Beach accelerate corrosion on fasteners, stucco, and exterior wood, which is exactly why we spec coastal-rated panels and fasteners rather than the inland standard. The dry Santa Ana wind events are the other side of it: panels need proper fastening and uplift resistance to ride those out. If you’re shoring the whole building up at once, that’s where the broader Roofing scope and the seismic work start to overlap.
Serving Long Beach, CA – Our Local Coverage Area
We serve Long Beach and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Metal Roofing in Long Beach

A typical single-family metal roof in Long Beach takes 3 to 6 working days from tear-off to final inspection. Complex or oversized roofs, deck repairs, and permitting review can stretch it. Call (888) 345-8164 for a timeline specific to your roof – estimates are free.
Yes. We pull the permit and see the inspections through. If your home falls in a Coastal Zone or historic context, extra review may apply, and we factor that into the schedule and quote. Call (888) 345-8164 to talk through what your property will need.
Metal roofing in Long Beach runs $15,000 to $40,000 installed, depending on size, deck condition, panel type, and permit scope. Standing seam lands toward the top, exposed-fastener panels toward the bottom, and stone-coated steel in between. Call (888) 345-8164 for an exact quote – estimates are free.
Metal handles the marine air and weight better than most. It’s lighter than tile, resists salt-air corrosion when correctly specified, and holds up to Santa Ana wind uplift. Homeowners restoring the Spanish Colonial look often choose stone-coated steel to get a tile appearance with less weight on an older frame.
Workmanship is backed by our 730-Day Done Right Promise; if it isn’t done right, we make it right. Manufacturer warranties on panels and finishes vary by product, and we spell those out in your written estimate so there’s no fine print to worry about. Call (888) 345-8164 to schedule a free estimate.
Book Your Free Metal Roofing Estimate in Long Beach
If you’re weighing metal for your Long Beach home, the next step is a free on-site estimate. Call (888) 345-8164 and a live person answers, day or night. We’ll inspect the roof, measure, check the deck, and hand you a written line-item quote with an honest timeline – no vague ballpark, no pressure. From there you decide. If the project grows into a full scope, our roofing service and our coverage across Long Beach handle the rest, and homeowners often pair the roof with Impact Windows & Doors in Long Beach. Background-checked, uniformed crews on every job.
Written by the team at Groundwork Construction Co.












