







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Impact Windows & Doors in Long Beach, CA: What the Job Actually Involves
Impact window and door installation in Long Beach runs $8,000 to $25,000 for a typical single-family home, and most full-house projects take two to four working days once materials land. You’re replacing glazing and frames with laminated, impact-rated assemblies built to hold together under wind-borne debris – and here that also means salt-rated hardware that won’t corrode in two summers off the port. Call (888) 345-8164 for a free on-site estimate.
How we run an impact window and door project, start to finish

Impact work isn’t a swap-and-go job. Here’s the real sequence, with the decisions you’ll be making along the way.
Stage 1: On-site measure and product selection (day 1, about 90 minutes)
We measure every rough opening, check the existing frames for rot and settling, and photograph anything that will change the scope. This is where you choose the frame material, glass package and operation type. On older Long Beach bungalows we also flag anything that suggests un-permitted past work around the openings, because that changes the trim and flashing detail.
Stage 2: Permit submittal and product order (weeks 1 – 3)
Impact assemblies are a permit item in Long Beach, and because much of the city sits in a Coastal Zone, some properties also carry design review. We prepare the submittal, then place the order once it’s approved. Factory lead times on impact units run longer than standard windows; three to six weeks is typical, longer on custom sizes.
Stage 3: Prep and demo (day 1 of install)
Furniture gets pulled back and floors covered. We remove the old sashes and frames, inspect the rough opening, and repair rot or framing before anything new goes in. That repair is the step cheap bids skip, and it’s why coastal homes leak after a “quick” install.
Stage 4: Set, shim, flash and seal (days 1 – 3)
Each unit is set level and plumb, shimmed, fastened per the manufacturer’s schedule, then flashed and sealed at the exterior. We use stainless or coated fasteners throughout. A whole-house package of twelve to twenty openings usually spreads across two to three days.
Stage 5: Inspection and final walkthrough (day 3 – 4)
We meet the inspector, then walk every opening with you: operation, locks, screens, sight lines and the interior trim finish. Anything you flag goes on a punch list and gets closed out. The whole job is covered by our 730-Day Done Right Promise, so if an operator or a seal fails, we come back.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll actually choose between
These are the decisions that move both performance and price. We’ll walk through each with samples in hand.
- Frame material – vinyl vs. aluminum vs. fiberglass. Vinyl is the value pick and holds up well against salt air. Aluminum is slimmer and stronger but needs a thermal break or it conducts heat. Fiberglass costs 20 – 30% more than vinyl and suits larger openings that would otherwise need steel reinforcement.
- Glass package. Laminated impact glass is the baseline. Adding a low-E coating and argon fill cuts heat gain, which matters on west-facing walls in Belmont Heights that bake from 3 p.m. on. It adds roughly $40 – $90 per opening.
- Operation type. Single-hung and casement are the least expensive. Sliders and fixed picture units run higher. We keep the existing operation where the opening allows, since changing type often triggers wider framing work.
- Impact entry and patio doors. A full impact door system costs more than a window of the same width – heavier hinges, multi-point locks, and a stiffer frame. Expect a meaningful jump per door versus per window.
- Interior finish. Drywall return, stained wood jamb or a simple casing. Stained wood looks right in a 1920s Spanish Colonial and costs more in both material and labor than a painted drywall wrap.
- Brand tier. We work with Andersen and Marvin among others. The top tier buys better hardware and tighter tolerances; the mid tier gets you the same impact rating at a lower number.
What Impact Windows & Doors cost in Long Beach, CA

Plan on $8,000 to $25,000 for a whole-house impact package. A partial replacement – say a front elevation or a few ocean-facing openings – lands in the $4,000 – $9,000 range once you’re past the minimum call-out. These are the variables that push a job toward either end:
- Opening count and size. More openings and bigger openings cost more, but the per-unit price drops once you’re past about eight units. Fixed picture windows are the cheapest per square foot; doors cost the most.
- Existing condition. Rot, settling or a previous un-permitted install means framing repair before installation. On east-side fourplexes and older bungalows we routinely find original knob-and-tube wiring and ad-hoc additions around the openings, and that adds labor.
- Frame and glass grade. Vinyl with standard laminated glass sits at the low end; fiberglass with low-E and argon sits at the high end.
- Permit scope. Straight impact replacement is one permit. Coastal Commission review or historic-district design review adds time and fees, and we’ll tell you up front whether your property is likely to trigger either.
- Access and height. Second-story and tight side-yard access slow the crew down, and that shows up in labor.
A written estimate from us is line-item: units, hardware, flashing, permit, labor and disposal, each priced. What typically isn’t included is interior repainting, any structural repair discovered after demo, and finish carpentry beyond standard trim. We show the number before we start and hold it – no change orders for things we should have caught on the measure. Call (888) 345-8164 for an exact quote.
See the difference
Before
After
Before
After
Before
AfterWhat Long Beach homes specifically do to this job
Long Beach is where very old housing stock meets very new regulation, and impact work feels it. A 1920s bungalow or a 1930s Craftsman fourplex in Rose Park or Belmont Heights sits in a Coastal Zone and often in a designated historic context, so the same small lot can trigger Coastal Commission review, historic-district design review and seismic retrofit requirements at once. You don’t hit that stack inland in Lakewood or Compton. Practically, it means we check design review before we order product, because a frame profile that fails review is a re-order and a six-week delay.
Then there’s the salt. The marine layer and air off the Port of Long Beach eat exterior hardware fast, and the original steel and wood frames on these bungalows are frequently corroded or rotted at the sill. That’s why we spec stainless or coated fasteners, corrosion-resistant hardware and proper flashing on every opening – and why termite and moisture damage around openings is a routine repair line, not a surprise. If you’re tying impact work into a wider envelope upgrade, it’s part of a full Windows & Doors in Long Beach scope. We cover all of Long Beach, and homeowners often pair this with an Aluminum Fence in Long Beach or an Iron Fence in Long Beach while the crew is on site. You can also see our Windows & Doors service for the broader lineup.
Serving Long Beach, CA – Our Local Coverage Area
We serve Long Beach and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Impact Windows & Doors in Long Beach

Most whole-house projects run two to four working days on site, but plan on six to ten weeks from signing to finish because of permit review and factory lead time on impact units. Call (888) 345-8164 to get a timeline for your specific openings.
Yes. Impact replacement is a permitted scope here, and properties in the Coastal Zone or a historic district can also face design review, which adds time. We prepare and pull the permits and meet the inspector, so that part isn’t on you.
In most cases, yes – a like-for-like replacement keeps the existing rough openings and doesn’t touch plumbing or electrical. The exception is older homes with un-permitted additions or knob-and-tube wiring near the frames, where we may need to open a wall to correct what we find.
Whole-house packages run $8,000 – $25,000, and partial elevations land around $4,000 – $9,000. The range depends on opening count, frame and glass grade, permit scope and any framing repair. Call (888) 345-8164 for an exact quote – estimates are free.
Every impact window and door project is covered by our 730-Day Done Right Promise, and the manufacturer’s product warranty sits on top of that. If something isn’t right, we come back and fix it.
Get a free estimate for impact windows and doors in Long Beach
Call (888) 345-8164 and a live person picks up, day or night. We’ll schedule an on-site measure, check whether your property triggers Coastal Zone or historic review, and hand you a line-item written estimate with the impact rating and hardware spelled out. Financing at 0% for 18 months is available, and projects over $10,000 get $1,000 off. We bring samples and answer questions until you’re ready to decide.
Written by the team at Groundwork Construction Co.












