







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Lynwood, CA: What It Costs and How Long It Takes
Metal roofing in Lynwood, CA runs $15,000 to $40,000 for a typical 1,200 to 2,000 sq ft roof, and most jobs take three to six working days from tear-off to final inspection. That’s the honest range for a 90262 house, not a teaser number. Call (888) 345-8164 and we’ll put an exact figure on paper after we see the deck and the pitch. Metal lasts longer than asphalt in our sun and rain, but the price swing between a basic exposed-fastener panel and a standing-seam system is wide, and it’s worth knowing why before you commit.
How We Run a Metal Roofing Job in Lynwood, Start to Finish

A metal roof isn’t just a swap of materials. The deck has to be sound, the underlayment has to be right, and the flashing around valleys and penetrations has to be rebuilt to shed water for decades. Here’s the sequence we run, and where you make decisions.
- Stage 1 – Tear-off and deck inspection (1 to 2 days). We strip the old roofing, then walk the sheathing board by board. On Lynwood’s older one-story homes we often find patchwork framing and rot around chimneys, and we stop and show you what’s there before doing anything else. You decide whether to replace the deck or sister the bad boards.
- Stage 2 – Repairs and underlayment (half a day to a day). Soft spots get replaced, then a high-temp synthetic underlayment or a peel-and-stick membrane goes down. You pick the underlayment grade here; it’s a small line on the estimate that decides how the roof handles the summer heat cycle.
- Stage 3 – Panel layout and flashing (1 day). We lay out panel spacing, set the eave and valley flashing, and cut the panels to length. Valley and wall flashing is where most leaks start on metal, so we spend the time.
- Stage 4 – Panel installation (1 to 2 days). Panels go on with the clips or fasteners your chosen system calls for. For a standing-seam roof the clips float the panels so they can move with heat; for exposed-fastener panels, the screws seat with a gasket. You’ve already chosen the system at the estimate.
- Stage 5 – Trim, finish, and inspection (half a day). Ridge caps, gable trim, and pipe boots go last, then we walk the roof with you and call for inspection. You sign off with the paperwork in hand.
Across all five stages, the homeowner usually makes three decisions: the panel system, the color and finish, and whether the deck gets fully replaced or patched. We bring samples to the estimate so you can make them without another trip. And every job is covered by the 730-Day Done Right Promise, so if something isn’t right after the crew leaves, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Metal Roofing Options You’ll Be Choosing Between
Two systems do most of the work in residential metal roofing, and a couple of smaller choices sit on top of them. Here’s how they stack up with the trade-offs spelled out.
- Standing-seam metal. Raised seams hide the fasteners and the panels float with heat, so they don’t back out over time. It’s the most durable and the most expensive, usually the top of the $15,000 to $40,000 range on a Lynwood home. Best for a homeowner staying put long-term.
- Exposed-fastener panels. Cheaper and faster to install. Every seam has screws with gaskets, so you should expect a gasket to shrink or a fastener to work loose over time. Fine for a garage or a patio cover, less ideal for the main house.
- Stone-coated steel (Boral makes a good one). A metal panel with a stone granule finish pressed to look like tile or shake. It gives you a heavier look than plain metal without the weight of actual tile on an older 1920s to 1960s home. Costs more than a painted panel; holds color well.
- Painted steel vs. aluminum. Steel is stronger and cheaper; aluminum resists corrosion better. On a Lynwood roof exposed to marine air rolling in off the coast, aluminum or a high-quality coated steel both hold up, but check the coating spec before you trade one for the other.
- Color and finish. A baked-on fluoropolymer finish (Tamko and Atlas both offer these) resists fading; a standard polyester finish is cheaper and fades sooner. You’re choosing a color you’ll look at for 40 years, so it’s worth the upgrade.
One honest note: metal is louder than asphalt in a hard rain, and on a house without good attic insulation you’ll hear it. We can talk through whether that matters for your home. Homeowners often pair this kind of exterior work with Window Replacement in Lynwood to tighten up the envelope at the same time.
What Metal Roofing Costs in Lynwood, CA

Metal roof installation in Lynwood runs $15,000 to $40,000, and the big swing comes from the system you pick and the condition of the deck underneath. Here’s how a written estimate breaks down, and what pushes a job toward the low or high end.
| Line item | Typical range |
|---|---|
| Tear-off and disposal of old roofing | $1,200 – $3,500 |
| Deck repair or replacement | $800 – $5,000 |
| Underlayment and flashing | $1,000 – $2,800 |
| Panel materials (depending on system) | $7,000 – $22,000 |
| Labor and installation | $3,500 – $8,000 |
| Permit and inspection | $300 – $900 |
What pushes a job high: a bigger roof, a full deck replacement on an older Lynwood home, a standing-seam system, complex valleys and pitch changes, or a roofline with several penetrations. What keeps it low: a sound deck, a simpler roofline, a smaller footprint, and an exposed-fastener panel on a garage or covered patio. Our estimates are line-item and upfront, so the number you see is the number you pay. Any work that surfaces after we open the roof gets shown to you before it happens, never billed as a surprise.
See the difference
Before
After
Before
After
Before
AfterWhat Lynwood Homes Specifically Do to a Metal Roofing Job
The typical Lynwood house is a one-story stucco-over-wood-frame home built between the 1920s and 1960s on a 5,000 to 6,000 sq ft lot, frequently with a detached garage at the back. Those decades matter: we regularly pull up old roofing and find patchwork framing from unpermitted additions and room conversions, so the deck is not always what the last roofer thought it was. The alley-facing garages off the north-south streets near Long Beach Blvd are a common spot for metal roofing over a shop or patio cover, and those structures often have older low-slope roofs that don’t drain the way they should. Lynwood’s wet winters and hot, dry summers are hard on underlayment, so a metal roof with proper flashing tends to outperform asphalt here over time. Because the city is densely built and much of the housing stock is old, permitting and inspection are routine for roof work, and we pull the permit and pass the inspection on every job. When the wider project scope comes up, this is often part of a full Roofing in Lynwood scope that includes the garage or patio structures, and we handle it as one job. If you’re also thinking about the exterior envelope, Impact Windows & Doors in Lynwood pair well with a new roof. You can read more about our broader service across Roofing.
Serving Lynwood, CA – Our Local Coverage Area
We serve Lynwood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Lynwood

Most Lynwood metal roofing jobs take three to six working days from tear-off to final inspection. A simple roof on a smaller house can finish in three; a larger or more complex roofline with deck repairs can run closer to six. Call (888) 345-8164 for a timeline based on your roof.
Yes, roof replacement and re-roofing in Lynwood require a permit and an inspection. We pull the permit for you and schedule the inspection; we don’t leave you to handle the paperwork. Call (888) 345-8164 to talk through what your project needs.
In most cases yes. Metal roofing is a re-roofing job, so the structure and plumbing stay where they are. If we open the deck and find rot or patchwork framing from an old unpermitted addition, we’ll show you before doing anything. Call (888) 345-8164 to schedule a look at your roof.
Metal roof installation in Lynwood runs from $15,000 to $40,000, with most jobs landing in the middle. The system you choose and the deck condition are the two biggest factors. Call (888) 345-8164 for an exact quote – estimates are free.
Our workmanship is covered by the 730-Day Done Right Promise, one of the longest in residential construction, on top of the panel manufacturer’s material warranty. If something isn’t right after the crew leaves, we come back and make it right. Call (888) 345-8164 to review the warranty with a written estimate in hand.
Get a Free Metal Roofing Estimate in Lynwood
If you’re weighing a metal roof for your Lynwood home, the fastest way to a real number is a free on-site estimate. Call (888) 345-8164 and a live person picks up, any hour. We’ll walk the roof, show you panel and color options, and hand you a written line-item quote with the permit included. We cover Lynwood and the surrounding area. No pressure, no change orders, no surprises.
Written by the team at Groundwork Construction Co.












