







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Lomita, CA: What They Cost and How Long They Take
Custom & Geometric Windows in Lomita usually run $2,800 to $9,500 per opening, and a typical whole-room or facade package lands around $12,000 to $26,000. Arch-tops, true-radius half-rounds, trapezoids and angles built to match a specific roofline are almost always special order, so plan on 6 to 10 weeks from template to final glaze. Call (888) 345-8164 and we’ll price your shapes against your actual walls, not a catalog page.
How we build a geometric window package, step by step

Curved and angled units fail on measurement, not on fabrication. That’s why the front half of this job is mostly template work, and it’s why we don’t order anything until we’ve had a second look at the rough opening with the stucco opened up.
- 1
Day 1 – Walk and measure. We log every opening, check square and level on the frames, confirm wall thickness and the existing header setup. You decide which shapes are fixed and which, if any, need to vent. Half-rounds over a pair of casements are common; an operable eyebrow is real money.
- 2
Days 2 to 3 – Template and confirm glass. For true-radius and angled units we build a physical template of the opening and transfer it to the manufacturer. This is the step that prevents a $3,000 arch from arriving an eighth of an inch out. You pick glass package, grille pattern and exterior trim color at this stage, and we put the spec sheet in writing before the order goes out.
- 3
Weeks 1 to 8 – Fabrication and permit. Custom units are built to order. In Lomita, window replacement of like-for-like size generally moves without a full building permit, but when we’re enlarging an opening or cutting a new one into a header, that’s structural and it gets pulled and inspected. We handle the filing.
- 4
Install week – Demo, flash, set. Usually 1 to 2 days per facade. We cut back stucco to the rough opening, check for rot and corroded flashing (often there), set and shim the unit, then flash and seal before anything gets closed up. Stucco patching and caulking finish the exterior.
- 5
Final day – Trim, glaze, walkthrough. Interior casing, hardware on any operable units, glass cleaning, and a joint inspection where we operate every sash and confirm the seal. That’s the day your 730-Day Done Right Promise starts.
You make three decisions in that sequence: which shapes operate, which glass package you want, and whether the trim is wood, PVC or aluminum-clad. Everything else we drive.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between
Most of the cost swing on geometric work comes down to four choices, and each one trades money against lifespan or maintenance.
- Frame material. Vinyl keeps the budget down but can’t be formed into tight radii cleanly, so true arches often push you to wood or aluminum-clad wood. Aluminum-clad wood is the sweet spot for coastal South Bay homes: painted wood inside, a factory finish outside that shrugs off salt air.
- Glass package. Single-pane is off the table for anything we install. Double-pane low-E with argon is standard; laminated glass adds impact and sound resistance and suits the Pacific Coast Highway side of town where road noise carries.
- Grille pattern. No grilles is the cleanest look for a big arch. Simulated divided lites cost more and read traditional. True divided lites on a curved unit are the priciest option and rarely worth it unless the house is period.
- Trim and finish. PVC and cellular trim won’t rot in the marine layer and cost less over 15 years than repainting wood every few. Wood casing looks better on a 1930s bungalow and we’ll tell you so.
On the door side, brands like Andersen and Marvin give the widest shape range and the tightest tolerances. If the project grows into a full facade, this becomes part of a Windows & Doors in Lomita scope and we quote it as one job.
What Custom & Geometric Windows cost in Lomita, CA

Expect $2,800 to $9,500 per geometric opening, or roughly $12,000 to $26,000 for a room-sized package of four to six units. A single arch-top fixed window with standard glass sits near the bottom of that per-unit range; a large operable radius unit with laminated glass and clad exterior lands near the top.
Five things move the number:
- Shape complexity. A half-round or a rectangle-with-arch is common and cheaper. Trapezoids, angled bays and full circles are one-off fabrication.
- Operable vs. fixed. Every hinge and latch on a curved sash adds cost and adds a leak path.
- Opening changes. Replacing like-for-like is one price. Cutting a new opening or enlarging one means header work, structural review and a building permit.
- Existing condition. Rot, corroded fasteners, and cracked stucco around the opening turn a half-day into a full day.
- Glass and finish grade. Low-E double-pane to laminated impact-rated is a meaningful jump.
A written estimate itemizes each unit by size and shape, glass spec, trim, patching, and permit cost. It won’t include interior drywall repair beyond the window reveal, or painting – we’ll flag both up front so nothing is a surprise later.
See the difference
Before
After
Before
After
Before
AfterWhat Lomita homes specifically do to this job
Lomita is roughly one square mile and fully built out, incorporated in 1964 and wrapped entirely by Torrance. There’s almost no raw land, so this work happens on 1920s to 1950s bungalows and early tract homes sitting on tight 5,000 to 6,000 sq ft lots, plus the 1960s and 70s stucco apartments along Lomita Boulevard and Pacific Coast Highway. Because the city runs its own building department and plan check on top of LA County coastal-area rules, second-story additions and rear extensions get reviewed lot by lot here in a way they don’t in sprawling Torrance.
That shapes window design directly. Near the PCH and Lomita Boulevard corridors, sight lines to the neighbor’s roofline often decide where a window can go before the plans ever reach plan check, so we frequently design around a specific adjacent pitch and height limit. And the damp morning marine layer plus salt-laden air is brutal on flashing and fasteners – corrosion-driven leaks around geometric openings are the most common failure we open up. In Lomita, we cover the whole city, from the corridor blocks to the quiet interior streets, and this fits neatly alongside Concrete Driveways & Concrete Work in Lomita if the exterior is getting a broader refresh.
Serving Lomita, CA – Our Local Coverage Area
We serve Lomita and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Custom & Geometric Windows in Lomita

Custom & Geometric Windows take about 6 to 10 weeks total, with most of that being special-order fabrication and the actual install running 1 to 2 days per facade. Call (888) 345-8164 to get a firm timeline for your shapes.
It depends on whether the opening changes. A same-size replacement usually doesn’t require a full building permit, but cutting a new opening or enlarging one into a header is structural and does get pulled and inspected. We handle the filing and the plan check either way – call (888) 345-8164 and we’ll tell you which applies to your wall.
Not on our written estimate. The number you see is the number you pay, and any hidden rot or corrosion we discover mid-job gets a photo and a conversation before we touch it. Call (888) 345-8164 for upfront pricing.
Usually yes. Most geometric window work is a like-for-like swap in the existing opening, which means no plumbing or framing changes at all. When you want a new opening cut, that’s when we bring in structural review and permits.
Every install is backed by our 730-Day Done Right Promise – if it’s not done right, we make it right – plus the manufacturer’s product warranty on the units and glass. Call (888) 345-8164 and we’ll walk you through both in writing.
Get a free estimate on custom & geometric windows in Lomita
Call (888) 345-8164 and a live person answers, any hour. We’ll set a time to walk your openings, template what needs templating, and hand you a written, itemized estimate with no surprises. If the work grows into full Windows & Doors, it’s still one contractor and one price. You can also see everything we do across Lomita, or pair this with Asphalt Driveways & Resurfacing in Lomita if the approach is due.
Written by the team at Groundwork Construction Co.












