







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Gutters & Accessories in Compton, CA: What the Job Actually Involves
Replacing gutters and accessories on a typical Compton home runs $1,400 to $4,200 for a full run of seamless aluminum with downspouts, hangers and leaf guards, and most single-story homes are torn off and rehung in one day. Two-story homes or anything with fascia damage push it to two days. The phone number for a free on-site estimate is (888) 345-8164. Below is what happens on the job, what your choices cost, and why Compton’s older stucco homes fail the way they do.
How a gutter job moves from first walk to final hanger

The sequence matters more than the sales pitch, so here it is in the order we work it.
Step 1: Load-in and roof edge inspection (under an hour). We start at the fascia, not the gutter. On Compton’s 1940s-1960s stucco homes, the fascia board behind the old gutter is often soft from years of overflow, and you can’t see that until the old run comes off. We check the roof edge, the drip edge, and the shingle course where water exits. You decide here whether we’re hanging new gutters onto sound wood or repairing fascia first.
Step 2: Tear-off and disposal (one to two hours). Old aluminum, steel or vinyl comes down and gets hauled off. We probe the fascia and the top plate with a screwdriver at every hanger location. Any rotted section gets marked and quoted as a line item before we cut into it, so you approve the number before the work happens.
Step 3: Forming and hanging (two to four hours). Seamless aluminum gets run on a machine at the curb, cut to exact length per run, and hung with a slight pitch toward the downspout. Hangers go in every 24 inches on center, closer in areas with heavy wind exposure. This is the stage where the pitch decision gets made, and it’s the single most common reason a gutter leaks at the seam instead of dropping water where it should.
Step 4: Downspouts, guards and accessories (one to two hours). Downspouts get routed and fastened, then the accessories get mounted: leaf guards, splash blocks, extensions, or a rain barrel diverter. On tight Compton side yards, the downspout route is a real decision, and we’ll walk it with you before drilling.
Step 5: Water test and cleanup (30 to 45 minutes). We run a hose at the high point of each run and watch water exit at the low point. Anything that pools, backs up or misses the splash block gets corrected before we leave. You get the final walk and the written workmanship guarantee at the same visit.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The gutter and accessory choices you’ll actually pick between
Most homeowners get handed a catalog and no guidance. Here’s the honest version of each choice.
- Seamless aluminum (5″ or 6″ K-style): The workhorse for Compton. Light, rust-resistant, formed on site so there are no mid-run seams, and it comes in about two dozen colors. The 6″ profile handles roughly 40% more water than 5″ and is worth it on any roof plane over about 1,000 square feet. This is what we install most often.
- Galvanized steel: Heavier and stronger than aluminum, holds up to ladders and tree limbs, but it will rust through at the seams over time in wet conditions. Suits homeowners who want a longer lifespan and don’t mind the weight and cost premium.
- Vinyl: The cheapest option and the one we steer people away from in Southern California. Intense summer sun makes vinyl brittle, and it cracks at the hanger point within a few seasons.
- Leaf guards (mesh, screen or reverse-curve): Mesh guards keep out leaves and most seed pods. Screen guards are cheaper and work fine for larger debris. Skip guards entirely if you have a low-slope roof section, because they’ll trap water rather than shed it.
- Downspout accessories: Splash blocks, buried extensions, and rain barrel diverters. On a small Compton lot with a narrow side yard, a buried extension that carries water to the alley or street is often the difference between a dry foundation and a wet one.
Materials in the same family come from the same supplier tiers we use across our work, whether that’s a GAF or CertainTeed roof above the gutter line or a Techo-Bloc paver apron at the base of a downspout. You choose quality, not whichever box was on the shelf.
What gutters and accessories cost in Compton, CA

Line-item ranges, so you can price the job before anyone knocks on your door:
| Item | Typical range |
|---|---|
| Seamless aluminum gutter, per linear foot | $6 – $12 |
| Full single-story home (roughly 150 – 200 LF) | $1,400 – $2,400 |
| Two-story or complex roofline | $2,400 – $4,200 |
| Downspouts, installed | $8 – $15 per LF |
| Leaf guards | $4 – $10 per LF |
| Fascia repair (rotted sections) | $250 – $900 |
| Buried downspout extension | $200 – $600 |
Four things push a Compton job toward the high end. The first is roofline complexity: a hip roof with multiple valleys and gables needs more downspouts and more careful pitch work than a simple gable. The second is fascia condition, which you can’t see until the old run is off. The third is material grade, since steel runs roughly double aluminum. The fourth is access, which on a narrow Compton side yard means a hand-carry job with no wheelbarrow or ladder staging room, and that adds labor.
A written estimate covers tear-off, disposal, seamless forming, hangers, downspouts, fasteners and a hose test. It typically does not cover fascia replacement, roof repair at the drip edge, or buried drainage lines, and each of those should be quoted as its own visible line item rather than folded into the total.
See the difference
Before
After
Before
After
Before
AfterWhat Compton homes specifically do to this job
The dominant housing in Compton is 1940s-1960s single-story stucco on tight R-1 lots, much of it infill and remodel work rather than new construction, and that history shows up right at the roofline. Fascia behind a 60-year-old gutter is often the original board, soft at the bottom edge where water has been wicking back for years. Original galvanized hardware and old hanger nails pull loose, so the new run usually gets fresh blocking. And because side-yard setbacks on these lots are narrow, running downspouts around the back of the house without landing them in a neighbor’s planter takes a real route decision, not a default.
The climate shapes the job too. Minimal freeze risk means we’re not sizing for ice dams, but intense summer sun makes vinyl fail fast and pushes aluminum expansion and contraction harder than in cooler zones. Santa Ana wind events are the other factor, and the reason we spec hangers more densely on any run facing an exposed side. Gutters usually fail on these homes at the hanger, not at the seam. If the roof edge and gutter are both aging out at once, it often makes sense to handle it as part of a full Roofing in Compton scope so the drip edge and gutter pitch get planned together, and if you’re considering a hardscape apron at the base of a downspout, our Roofing work with Quikrete and Oldcastle products pairs with that. We cover all of Compton, from the 90222 core out through 90220, and homeowners often pair a gutter refresh with Sliding & Patio Doors in Compton when water damage near the door has been a recurring problem, or with Impact Garage Doors in Compton when the full exterior envelope is getting updated at once.
Serving Compton, CA – Our Local Coverage Area
We serve Compton and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked: gutters and accessories in Compton

Most single-story Compton homes are completed in one day, roughly four to six hours on site, and two-story homes usually take a day and a half. The tear-off, seamless forming and hanging stages dominate the clock, and fascia repair is the one thing that can stretch it. Call (888) 345-8164 and we’ll give you a realistic day count on the walk-through.
Gutter replacement itself generally does not require a permit because it’s a surface-mounted exterior element rather than a structural or plumbing change. Fascia replacement on a home in a flood or high-wind zone, or any change that ties into the roof structure, can trigger a plan check. We pull the permits on the work that needs them and pass inspection, and our written estimate tells you clearly which side of that line your job falls on.
Yes. Gutters mount to the fascia and the drip edge, so the roof covering and everything inside the walls stays in place. The one exception is a rotted fascia that has to come off, which is a carpentry fix at the roof edge, not a roofing job. If we find that mid-install, we quote it as a line item and you approve it before we touch it. Call (888) 345-8164 to schedule the inspection.
Most Compton homes land between $1,400 and $4,200 for seamless aluminum with downspouts, with leaf guards adding $4 to $10 per linear foot and fascia repair running $250 to $900. Where you land depends on roofline complexity, material grade, fascia condition and side-yard access. Our pricing is upfront and fixed, so the number in the written estimate is the number you pay. Call (888) 345-8164 for an exact quote.
Our workmanship is covered by the 730-Day Done Right Promise, one of the longest residential workmanship guarantees in the trades. If a hanger pulls loose, a seam leaks, or a downspout comes unfastened within that window, we come back and make it right. Material warranties pass through from the manufacturer, and we’ll walk you through what each covers on the final inspection.
Get a free gutter estimate in Compton
Call (888) 345-8164 to schedule a free on-site estimate for gutters and accessories in Compton. A live person answers around the clock, so there’s no voicemail to leave and no waiting until Monday. On the visit, we walk the roofline, check the fascia, and hand you a written estimate with every line itemized: gutters, downspouts, guards, and any fascia repair. Call today and we’ll get you priced.
Written by the team at Groundwork Construction Co.












