







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Vanities, Tile & Fixtures in Lomita, CA: What the Job Costs and How Long It Takes
Replacing a vanity, tiling a floor or shower surround, and swapping out fixtures in Lomita usually runs $9,000 – $28,000 for a full bathroom’s worth of work, or $900 – $3,000 if you’re only doing the vanity and fixtures. Most jobs take 5 – 12 working days once materials are on site. Call (888) 345-8164 and we’ll walk your Lomita bathroom and put real numbers on it, free.
How our Vanities, Tile & Fixtures work actually runs, stage by stage

Every bathroom we touch in Lomita follows the same sequence. Here’s what happens, roughly when, and what you’re deciding at each point.
Stage 1: On-site measure and material selection (day 1, about 90 minutes)
We measure the vanity alcove, check the drain and supply rough-in locations, and confirm whether the existing tile sits on a mud bed or backer board. You’ll decide the vanity width and depth, whether the top is quartz, cultured marble, or tile, and the fixture finish (chrome, brushed nickel, matte black). Bring your Pinterest board; we’ll tell you what fits the space and what doesn’t.
Stage 2: Demo and rough-in inspection (days 2 – 3)
Old vanity, top, mirror, and tile come out. This is where Lomita surprises show up: 1950s bungalows on 5,000 – 6,000 sq ft lots frequently hide galvanized supply lines and cast-iron drains that have outlived their usefulness. If we find them, we document it with photos and get your approval before touching anything. If the scope changes, the price changes on paper – not by surprise.
Stage 3: Substrate prep and waterproofing (days 3 – 4)
Backer board goes down, seams get taped and mudded, and a waterproofing membrane goes on wet areas. For Lomita you want this done right: the marine layer and damp morning fog drive moisture into walls, and a poorly sealed shower pan will rot framing faster here than it would inland. We let the membrane cure overnight before any tile goes near it.
Stage 4: Tile setting and grouting (days 5 – 9, depending on square footage)
Floor tile first, then shower walls if you’re doing a surround, then grout after the thinset cures. You’ll decide layout (stacked, herringbone, offset), grout color, and whether to use a penetrating sealer. We schedule tile work separately from plumbing so the tile has time to set correctly.
Stage 5: Vanity install, fixture set, and final walkthrough (days 10 – 12)
Vanity cabinet goes in, top gets set and caulked, sink and faucet get connected, toilet gets reset, mirror and accessories go up. We test every drain and supply, run the shower, and check for leaks before we call you in. Final walkthrough takes about 30 minutes. That’s when you sign off and the 730-Day Done Right Promise kicks in.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The choices you’ll actually make: vanities, tile, and fixtures
Here’s the honest trade-off on each decision that moves both your budget and your long-term satisfaction.
- Vanity cabinet grade: Stock cabinets (particleboard box, laminate or veneer face) run cheap and fit fast. Semi-custom plywood boxes with a KraftMaid or similar line last 20+ years and give you drawer configuration options stock won’t. In a Lomita bungalow where the vanity alcove may not be square, semi-custom is usually worth the extra.
- Vanity top material: Cultured marble is the value play and cleans easily. Quartz or Cambria reads higher-end, resists stains, and won’t chip like cultured marble at the edges. Tile tops look great but grout lines in a bathroom top are a maintenance headache.
- Floor tile: Porcelain is the workhorse – dense, water-resistant, and fine for a Lomita bathroom. Natural stone (travertine, marble) is beautiful but needs sealing every 1 – 2 years and is more slippery when wet. Ceramic is the budget option; it’s fine in low-traffic baths.
- Shower wall tile: Large-format porcelain (12×24 or bigger) means fewer grout lines and faster install. Subway tile costs less per square foot but takes longer to set. Both work; the decision is aesthetic and labor-driven.
- Fixtures: Kohler and similar mid-to-premium lines hold up under daily use, and parts are available years later. Big-box house brands are fine but replacements get harder to source. Faucet finish matters too: brushed nickel hides water spots better than polished chrome in a damp coastal climate.
What Vanities, Tile & Fixtures costs in Lomita, CA

Most Lomita jobs land between $9,000 and $28,000. That’s the full-scope number – vanity, tile, fixtures, and everything behind the wall. Here’s what pushes a job toward the low or high end.
| Line item | Typical range |
|---|---|
| Bathroom vanity installation | $800 – $3,000 |
| Tile floor or shower surround (labor + material) | $2,500 – $9,000 |
| Fixture set (faucet, shower trim, toilet, accessories) | $800 – $3,500 |
| Plumbing rough-in adjustments (if needed) | $400 – $1,800 |
| Waterproofing and substrate prep | $600 – $1,500 |
- Size of the bathroom: A 5×8 hall bath vs. a 10×12 primary bath changes tile square footage and vanity width. That’s the single biggest swing.
- Existing condition: A 1950s Lomita bungalow with original galvanized plumbing will cost more to bring to code than a 1990s build. We tell you which before we start.
- Relocating plumbing or electrical: Moving the toilet or sink drain adds rough-in labor and possibly a permit amendment. Moving a vanity outlet requires a licensed electrician.
- Material grade: Porcelain and cultured marble keep costs down. Natural stone, large-format tile, and custom vanities push toward the high end.
- Permit scope: Cosmetic work (vanity swap, fixture replacement) usually doesn’t need a permit. Structural moves, new drains, or electrical relocation do – and that’s a line item you’ll see in the written estimate, not a surprise later.
Every written estimate is line-itemed. What’s included: labor, demolition, haul-away, substrate prep, and waterproofing. What’s not: material upgrades above the allowance, hidden damage found during demo (we show you photos before charging), and any permit fees we haven’t pulled.
See the difference
Before
After
Before
After
Before
AfterWhat Lomita homes specifically do to this job
Lomita is a one-square-mile Harbor Gateway city, incorporated in 1964, completely surrounded by Torrance. Almost no undeveloped land exists here, so bathroom work is almost always remodel on a tight infill lot, not new construction. The most common housing stock we see is 1920s – 1950s small single-family bungalows on 5,000 – 6,000 sq ft lots, plus 1960s – 70s stucco apartments along the Pacific Coast Highway and Lomita Boulevard corridors.
What that means for your job: old wood-frame houses with knob-and-tube wiring and galvanized plumbing tucked behind the vanity wall. We plan for it. City of Lomita’s building department runs plan check locally, layered over LA County coastal-area rules for anything structural, so permits and inspections take longer than in sprawling neighboring Torrance or unincorporated county land. And the marine layer plus salt air means your bathroom’s waterproofing details matter more than in inland cities. Damp morning fog drives rot; a poorly sealed shower pan will fail here in years, not decades. We spec corrosion-resistant fasteners and let waterproofing cure fully before tiling.
Serving Lomita, CA – Our Local Coverage Area
We serve Lomita and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Vanities, Tile & Fixtures in Lomita

Most jobs take 5 – 12 working days, depending on tile square footage and whether plumbing needs moving. Cosmetic vanity-and-fixture swaps can wrap in 2 – 3 days. Call (888) 345-8164 for a realistic timeline on your specific bathroom.
Cosmetic work – new vanity, new tile, fixture replacement in the same locations – usually doesn’t require a permit. Moving a drain, relocating electrical, or altering walls does. We check with the City of Lomita building department before work starts and pull permits when needed.
Yes, in most cases. The existing drain and supply locations stay put, and we build the new vanity around them. If the new vanity is a different width or depth, we check clearances first; that’s part of the on-site measure.
Full-scope jobs run $9,000 – $28,000; vanity-only installs run $800 – $3,000. The biggest cost drivers are bathroom size, existing plumbing condition, and material grade. Every written estimate is line-itemed with no change orders unless you approve them.
All vanities, tile, and fixture work in Lomita is covered by the 730-Day Done Right Promise. If it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction.
Get a free on-site estimate for Vanities, Tile & Fixtures in Lomita
Call (888) 345-8164 and a live person will pick up, any hour. We’ll schedule a free on-site estimate, measure your bathroom, and hand you a line-itemed written quote with material options and a firm timeline. No pressure and no surprises. If you’re pairing this with a bigger project, it’s often part of a full Bathroom Remodeling in Lomita or our broader Bathroom Remodeling service. We cover all of Lomita and nearby communities; homeowners often pair this with Tile Roofing in Lomita or Specialty Roofing in Lomita while we’re already on site.
Written by the team at Groundwork Construction Co.












