







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterFence Gates in Long Beach, CA
A fence gate in Long Beach typically runs $450 to $1,900 installed, depending on width, material, and whether it’s a walk gate or a drive gate. A standard 4-foot cedar walk gate with galvanized hardware lands near the low end; a 12-foot double drive gate with steel framing and an automatic opener pushes toward the top. We build gates that line up with the fence, swing true for years, and don’t sag three months after installation.
Gates are the part of a fence that gets used every day and the part most contractors treat as an afterthought. A gate that drags on the concrete, latches loosely, or warps because the frame was built too light is a daily annoyance. We build the gate as a structural piece, not a cosmetic one. If you’re planning a full perimeter project, start with our Fence Installation page for the broader scope, then come back here for the gate details. Call (888) 345-8164 and a live person picks up, day or night.
We’re Groundwork Construction Co. of Long Beach. Our technicians bring up to 12 years of experience to every gate, and every project is backed by our 730-Day Done Right Promise. If the gate doesn’t swing right, we come back and make it right.

Key Takeaways
- Walk gates in Long Beach usually cost $450-$900; drive gates run $1,100-$1,900 before automation.
- Salt air near the coast eats cheap fasteners fast; we spec hot-dipped galvanized or stainless hardware on every gate within two miles of the water.
- Long Beach permits a fence or gate up to 6 feet in the rear and side yards by right; front-yard gates and anything taller need a zoning check before we build.
- Every gate we install carries the 730-Day Done Right Promise and upfront pricing, so the number on the estimate is the number you pay.
When You Need Fence Gates
Most gate calls we get in Long Beach fall into a handful of patterns. Some are new builds where the gate is part of a full fence run. Others are repairs where an existing gate has finally given up. Here’s what tends to trigger the call.
- The gate sags and drags on the ground. In older neighborhoods like Belmont Heights and Rose Park, we regularly see gates hung 15 or 20 years ago where the hinge-side post has started to lean. The wood is fine; the post footing has rotted or shifted. Rebuilding the gate on a new post solves it. Patching the sag doesn’t.
- You need driveway access and the current gate is manual. A lot of Long Beach driveways run tight against the property line. A double swing gate or sliding gate gives you clearance a single swing can’t. If you’re tired of getting out to open it, we can frame for an automatic opener on the original build so it’s simple to add later.
- You want a side-yard gate for privacy or pets. Wrigley, Cal Heights, and Bixby Knolls homes often have a side yard that needs a 3- to 4-foot gate to keep dogs in and strangers out. We build these to match the fence height and picket or panel style so the run looks continuous.
- The latch won’t stay closed. Cheap latches on coastal properties corrode and fail within a few years. Salt air is relentless here. We spec marine-grade or hot-dipped galvanized latches that hold up to the humidity and the onshore breeze.
- You’re adding a pool and need a code-compliant gate. California pool safety rules require self-closing, self-latching gates with specific hardware. If a pool is going in, the gate has to meet the standard, not just look good.
- The old gate is a mismatch. Sometimes a gate was added years after the fence and never matched. We build gates to match the existing fence’s picket spacing, rail height, and finish so the whole run reads as one piece.

Our Fence Gates Process
We keep the process tight because a gate is a small job with a lot of detail. Here’s how we run it from first call to final swing.
- Free on-site estimate and design consult. We walk the property, measure the opening, check the soil and existing posts, and talk through material, width, swing direction, and hardware. You get a written, upfront price before any work starts. No surprises, no change-order games.
- Material and hardware selection. We build in cedar, redwood, pressure-treated pine, composite, and steel-frame options. For hardware we pick hot-dipped galvanized or stainless on anything near the coast. We don’t stock a truck of parts; we spec the right pieces for your gate and bring them to the job.
- Post and footing prep. The gate post carries the whole load. We set it in concrete at the proper depth, brace it, and let it cure before hanging anything. This is where cheap gate jobs fail. A light post and a shallow footing equals a sagging gate in a year.
- Gate framing and assembly. We build the frame with proper diagonal bracing so the gate resists racking. The swing is level, the gap at the bottom clears the concrete by the right amount, and the latch lines up cleanly.
- Hanging, hardware, and adjustment. Hinges, latch, and any automation go on at the end. We test the swing, adjust the hinges, and confirm the latch catches every time. Most gate jobs are completed in a single visit once materials are in hand.
- Final walkthrough and warranty handoff. We walk the gate with you, show you the hardware, and hand over the 730-Day Done Right Promise in writing. If anything’s off in the first two years, we come back.
Fence Gates Pricing in Long Beach
Gate pricing in Long Beach is driven by width, material, and hardware more than anything else. Here’s a straight read on what things run in this market. Every estimate we give is upfront and written, and the number you see is the number you pay.
| Gate type | Typical installed range | What drives the price |
|---|---|---|
| Standard walk gate (3-4 ft, wood) | $450-$750 | Width, cedar vs. pressure-treated, hinge and latch grade |
| Wide walk gate (5-6 ft, wood or composite) | $700-$1,100 | Frame bracing, post size, composite vs. wood |
| Double drive gate (10-12 ft, wood) | $1,100-$1,700 | Span, center drop rod, heavier posts, footing depth |
| Steel-frame drive gate | $1,400-$1,900 | Steel gauge, powder coat, hardware |
| Automatic opener (add-on) | $900-$1,800 | Opener brand, wiring distance, safety sensors |
| Pool safety gate hardware retrofit | $250-$500 | Self-close hinge, latch code compliance, gate adjustment |
A few things move the number up or down. Coastal hardware adds cost but saves you a repair in three years. Wider gates need heavier posts and deeper footings, so the labor is higher. Composite and steel-frame gates cost more in materials but hold their shape better over time. Long Beach’s marine layer and the salt in the air wear hard on any gate within a couple miles of the water, so we don’t cut corners on fasteners there.
We offer $1,000 off projects over $10,000 and 0% financing for 18 months on qualifying work. If the gate is part of a bigger fence or driveway project, those offers apply. Every estimate is free, and the price you’re quoted is the price you pay. Call (888) 345-8164 for a free estimate and a real person answers, any hour.
Gates That Match the Fence and Hold Up to the Coast
A gate that doesn’t match the fence looks like an add-on. We build gates to the same picket spacing, rail height, and finish as the rest of the run, so the whole line reads as one piece. That matters in neighborhoods where curb appeal counts and in any project where a mismatched gate would be the first thing a buyer notices.
Materials are where a gate either lasts or doesn’t. We work with brand partners across the trades, from composite and stone to roofing and windows, because the same principal applies everywhere: pick materials that will hold up, then back the work in writing. On gates, that means calling out the hardware and lumber we spec on the estimate instead of leaving it to “whatever’s available.” A gate is built to last, backed in writing.
If your gate project ties into a larger perimeter or driveway job, our broader Fence Installation in Long Beach page covers the full scope, and our home page shows the other services we run. We handle gates as a standalone job and as part of a full property upgrade.
Fence Gate Repair or Replace: Which One Makes Sense?
If the post is solid and the frame is intact, a repair often makes sense: rehang the gate, replace the hinges and latch, adjust the swing. If the post is rotted, the footing has shifted, or the frame has racked beyond adjustment, replacing the gate is the honest answer. We tell you which one applies on site, not after we’ve already started. Repairs typically run $150-$400; a replacement gate is the higher numbers in the table above. If you’re deciding between patching and rebuilding, a free estimate gives you a clear comparison before you spend anything.
Permits and Code for Long Beach Gates
Most residential fence and gate work in Long Beach up to 6 feet in the rear and side yards doesn’t need a building permit, but front-yard fences and gates have height limits under city zoning, and anything taller than the standard needs a review before we build. Pool gates fall under separate state pool safety rules that require self-closing and self-latching hardware. We check the requirements for your address as part of the estimate, so the gate we build is the gate that passes. That’s part of why projects go smoothly: the permitting questions get answered before a single post goes in.
Why Homeowners in Long Beach Call Us for Gates
- 730-Day Done Right Promise. Every gate is covered for two years. If the swing drifts, the latch fails, or the frame warps, we come back and fix it.
- Live person, 24/7. No voicemail, no waiting until Monday. When you call (888) 345-8164, a real person answers.
- Background-checked, uniformed technicians. The people who show up at your property are verified and in uniform, not an unmarked crew.
- Upfront pricing, no surprises. The estimate is written and the price doesn’t move unless you change the scope.
- Trusted brand partners. We work with proven manufacturers across every trade so gates are built with materials we can stand behind, not whatever’s on sale.
Where We Build Fence Gates in Long Beach
We build gates across Long Beach and the surrounding neighborhoods, from the bluff-top homes in Bluff Park to the inland blocks of Lakewood Village and the family homes in Bixby Knolls. Coastal properties near Belmont Shore and Naples need extra attention to hardware and fasteners because of the salt air; inland properties deal more with dry-season wood movement and shrink. We adjust the material spec to the block, not to a single template.
Long Beach also has a lot of alley-facing garages and side-yard access points. Those gates get used daily, so we build them heavier than a decorative garden gate. If your gate opens onto an alley or a driveway, tell us on the call and we’ll spec it accordingly.
FAQs – Fence Gates
How much does a fence gate cost in Long Beach?
A standard wood walk gate in Long Beach typically installs for $450-$900, and a double drive gate runs $1,100-$1,900 before any automatic opener. Steel-frame and composite gates sit at the higher end. The exact number depends on width, material, and hardware, so a free estimate gives you the real figure. Call (888) 345-8164 for an exact quote.
Can you build a gate that matches my existing fence?
Yes. We build gates to match the picket spacing, rail height, finish, and style of your existing fence so the run looks continuous. Bring us a photo or let us measure on site. Call (888) 345-8164 to schedule a free design consult.
Do I need a permit for a gate in Long Beach?
Most rear and side-yard gates up to 6 feet don’t need a building permit, but front-yard gates and anything taller fall under city zoning limits and may need a review. Pool gates also have their own state safety rules. We check the requirements for your address as part of the free estimate. Call (888) 345-8164 and we’ll walk you through it.
Can you install an automatic gate opener?
Yes. We frame the gate for automation during the build so adding an opener later is simple, or we install the opener on the original job. Openers typically run $900-$1,800 installed depending on brand and wiring distance. Call (888) 345-8164 for a free estimate that includes opener options.
How long does a gate installation take?
Most gate installations are completed in a single visit once materials are on hand. If the gate is part of a larger fence run or needs a new post footing to cure first, it may take two visits. Set-up and cure time on footings is the usual variable. Call (888) 345-8164 to get a timeline for your specific property.
Get a Free Fence Gate Estimate in Long Beach
If your gate is sagging, sticking, or missing entirely, we can get you a straight answer and an upfront price. Calls are answered by a live person 24/7, estimates are free, and every gate we build is backed by the 730-Day Done Right Promise. Call (888) 345-8164 today and we’ll get your gate on the schedule.
Written by the team at Groundwork Construction Co. of Long Beach, serving Long Beach.


