







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Lynwood, CA: What the Job Actually Involves
Custom & geometric windows in Lynwood typically run $6,500 to $19,000 installed, with most single-arch or angled-bay projects landing between $8,000 and $13,000, and a full set of radius and trapezoid units across the front of a house pushing toward the top. The work takes three to six weeks from template to final trim because every unit is built to the opening, not pulled off a shelf. Call (888) 345-8164 and we’ll walk your openings, take measurements, and put real numbers in writing.
How We Build Custom & Geometric Windows, Stage by Stage

These windows aren’t a same-week swap. The shape drives everything, so the sequence matters more than the speed.
Day 1: Walk and rough measurements
We measure every opening, note the existing framing, and photograph the wall from inside and out. You decide which openings get a true arch, which get a radius top, and which get a geometric pattern like a half-round or a segmental arch. This visit takes about 90 minutes on a typical Lynwood one-story.
Days 2 – 7: Template and order
For true arches and angled units, the manufacturer needs a physical template of the opening, not just a number. We build that template, confirm the glass spec and grid pattern with you, and place the order. This is the decision window: material, finish color, glass package, and whether the unit is fixed or operable. Lead times run three to five weeks because geometric units are made to order.
Days 8 – 20: Build time
The factory builds the units while we prep. We confirm the delivery date, order any trim or flashing stock, and coordinate a day when the wall is open for the shortest possible stretch. You don’t need to be home for this stage.
Days 21 – 25: Demo and install
We pull the old unit, check the rough opening for rot and level, and set the new frame. A single arch or geometric unit takes a day; a full set of four to six openings takes three or four. We flash the exterior, seal the interior, and leave the wall weather-tight the same day.
Days 26 – 30: Trim, finish, inspection
Interior casing, exterior trim, and caulk go on, then the job is ready for the rough and final inspection if the scope triggered a permit. You get a walkthrough and a written record of what was installed and under what warranty.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between for Custom & Geometric Windows
Most of the decisions on this job come down to four categories. Here’s the honest trade-off on each.
- Material: wood, fiberglass, or aluminum-clad. Wood gives the cleanest look on a true arch but needs repainting every few years. Fiberglass holds its shape on radius units and handles Lynwood’s dry summers without warping, at a higher cost. Aluminum-clad is the middle path: wood inside, a baked finish outside that survives sun and rain with little upkeep. Our windows & doors service carries Andersen and Marvin lines that work well on geometric shapes.
- Glass package. A basic double-pane is fine on a north wall. On the south and west faces, a low-E coating and argon fill cut heat gain enough to notice on a July afternoon. Tinted or patterned glass on a half-round transom is a design choice, not an efficiency one.
- Fixed vs. operable. Most geometric units are fixed. Operable arches exist but cost 30 to 40 percent more and complicate the hardware. If you want ventilation, pair a fixed arch with a standard operable unit below it.
- Grid and trim pattern. True divided lites cost more and read as traditional; simulated divided lites give the look for less. On a geometric unit the muntin layout has to be drawn, so this decision gets locked early.
What Custom & Geometric Windows Costs in Lynwood, CA

Plan on $6,500 to $19,000 for a typical residential set, with a single arch or radius unit running $2,200 to $4,800 installed and a full front elevation of geometric windows landing in the $12,000 to $19,000 range. A few variables push a job from the low end to the high end:
- Shape complexity. A segmental arch is cheaper than a true half-round; an angled bay or trapezoid adds cutting and template cost.
- Opening condition. On Lynwood’s older homes, we often find patchwork framing or rot once the old unit comes out, which adds framing time.
- Size and count. One large picture arch costs more than two smaller units of the same total area.
- Material grade. Wood sits at the low end, fiberglass and aluminum-clad at the high end.
- Permit scope. A like-for-like replacement that keeps the opening size may not need a permit; enlarging an opening or cutting a new one does, and that adds inspection time.
Your written estimate lists the units, glass spec, trim, installation labor, and permit fees as separate lines. It typically excludes interior drywall repair beyond the window opening and any structural work if the wall needs a header upgrade, which we’d flag before work starts.
See the difference
Before
After
Before
After
Before
AfterWhy Lynwood Homes Make This Job Different
The typical Lynwood house in the 90262 ZIP is a one-story 1920s – 1960s stucco-over-wood-frame home on a 5,000 to 6,000 square foot lot, and many of them have had unpermitted room additions or converted garages over the years. That history matters here: when we open a wall for a new geometric window, we routinely find patchwork framing, and in some 1960s builds aluminum wiring or older two-wire circuits that have to be handled before the wall closes back up. On the alley-facing detached garages off Long Beach Blvd, some of those structures were built out as living quarters without permits decades ago, so if a custom window is part of a garage-to-ADU conversion, the permit status has to get sorted before any new opening is legal. Lynwood’s mild, wet winters and hot, dry summers mean year-round work is possible, but we schedule exterior sealing around rain, and summer heat makes the glass package decision more than cosmetic on west-facing walls. If the project is part of a wider job, see our Windows & Doors in Lynwood page, and homeowners often pair this with Concrete Driveways & Concrete Work in Lynwood when the front elevation is getting a full refresh.
Serving Lynwood, CA – Our Local Coverage Area
We serve Lynwood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked About Custom & Geometric Windows in Lynwood

Three to six weeks from template to finished trim, with the install itself taking one to four days depending on how many openings. The bulk of that time is factory build, since geometric units are made to order. Call (888) 345-8164 to get a firm schedule for your openings.
It depends on whether the opening size changes. A like-for-like replacement in the same opening often doesn’t require one, but enlarging an opening, cutting a new one, or changing the structural header does, and so does any window tied to an ADU or garage conversion. We check the scope against Lynwood’s requirements and pull the permit when it’s needed. Call us and we’ll tell you exactly what your job triggers.
In most cases, yes. A same-size swap doesn’t touch plumbing or framing. Enlarging an opening can mean moving a header, and if a wall has plumbing in it, we plan the layout around it. We confirm this at the walkthrough before anything is ordered.
Installed, $6,500 to $19,000 for a typical set, with a single arch at $2,200 to $4,800. Material, shape, opening condition, and permit scope are the main levers. Call (888) 345-8164 for an exact quote; estimates are free.
All of our work is covered by the 730-Day Done Right Promise, backed in writing. If something isn’t right, we make it right. The window units also carry the manufacturer’s own warranty, which we document for you at the walkthrough.
Get a Free Estimate on Custom & Geometric Windows in Lynwood
Call (888) 345-8164 for a free on-site estimate on custom & geometric windows in Lynwood. A live person answers, day or night. We’ll measure your openings, talk through shape and material, and leave you with a written, upfront price with no surprises. If you’re weighing a bigger refresh, our Windows & Doors team covers the full scope, and you can see everything we do across Lynwood.
Written by the team at Groundwork Construction Co.












