







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Gardena: What It Costs and How Long It Takes
A Tub-to-Shower Conversion in Gardena runs $3,500 to $10,000 and typically takes 5 to 10 working days once demolition starts. The old tub and its surround come out, the drain gets repositioned to fit a shower pan, waterproofing and tile go in over a properly prepared substrate, and a new valve and trim finish it off. Most homeowners here choose it because a tub they no longer use eats floor space in a hall bath. Call (888) 345-8164 and we’ll quote your exact layout, free.
How Groundwork Handles the Job, Stage by Stage

We sequence a conversion the same way every time, and we tell you up front which days you’ll have a usable bathroom and which days you won’t.
Stage 1: Measure, scope, and written quote (1 visit)
We take actual dimensions of the alcove, check the drain location, and look at what’s behind the wall around the valve. If the existing tub is cast iron, we note it now, because that changes demo labor. You get a line-item quote before anything gets ordered. Nothing moves until you approve it.
Stage 2: Permits and product selection (3 to 10 days of calendar time)
Pull a permit if the project needs one. Most Gardena plan-check submissions move through the city’s building department in one to two weeks, and we handle the submittal. At this stage you pick the pan type, wall finish, and valve trim. These are the decisions that sit on the critical path, so we put the choice sheet in your hands early rather than at the last minute.
Stage 3: Demo and rough-in (days 1 and 2)
Day 1 is teardown: tub out, surround and backer down to studs, old valve examined. Day 2 is rough-in, where the drain and mixing valve are set to the new shower’s geometry and any rotted framing or failing subfloor gets swapped. A tub-to-shower conversion almost always needs a drain relocation, so you’re cutting slab or subfloor, not just tiling over.
Stage 4: Waterproofing and inspection (day 3)
The pan gets set and the walls get a bonded waterproofing membrane. We schedule the rough and pan inspection when your project requires it, then wait for the sign-off before any tile goes up. That wait is a day or two, and skipping it is how shower failures start. You’ll see the membrane assembly at this point if you want to look at it.
Stage 5: Tile, glass, trim, and walkthrough (days 4 to 8)
Tile and grout, then the glass door or curtain rod, the valve trim, and a final flood test and cleanup. We walk the finished shower with you, show you the grout care instructions, and hand over the paperwork. Waterproofing behind the finish is covered by our 730-Day Done Right Promise, which is one of the longest workmanship guarantees on residential work you’ll find in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Once the tub is out, the decisions are yours. Here’s the honest read on each.
- Acrylic or fiberglass pan and surround: The fastest, least expensive route, often near the low end of the $3,500 to $10,000 range. One-piece units go in quickly, wipe clean easily, and hold up fine for a hall bath or rental. The trade-off is that they look like what they are, and a chip or crack is hard to patch invisibly.
- Tiled walls over a waterproof membrane: The middle and upper part of the price range. Porcelain or ceramic tile gives you a floor-to-ceiling finish that matches the rest of the house and survives decades. Grout needs sealing and the tile work adds three to five days. This is the version Gardena homeowners tend to pick for the primary bath.
- Solid-surface panel systems: A middle path with fewer seams than tile and no grout to scrub. It handles moisture well but the panel sizes constrain your layout, so it fits some alcoves better than others.
- Shower door material: Framed vs. frameless glass. Frameless looks cleaner in a small hall bath and costs more; framed is cheaper and more forgiving if the walls aren’t perfectly plumb.
- Valve and trim grade: A basic valve with a standard finish versus a thermostatic valve with a brushed finish. This is a small slice of the budget but it’s the part you touch every day, so don’t cheap out on it. Kohler trim, for example, holds up well.
- Wall and floor finish grade: A single subway tile keeps the price down. A larger-format or patterned tile costs more in material and labor but changes the whole room.
What Tub-to-Shower Conversion Costs in Gardena, CA

For a standard alcove conversion, budget $3,500 to $10,000. That range holds for most single-story Gardena homes. The variables that push a job toward either end:
- Size and layout: A 60-inch standard alcove sits near the low end; a five-foot-plus footprint that requires moving the valve or drain to the opposite wall adds cost.
- Existing condition: Rot behind the surround, failing subfloor, or a slab that needs cutting pushes the job up. It’s common in older homes.
- Plumbing and electrical: Relocating a drain is routine; relocating a vent stack or adding electrical for a lighted niche adds real money. Leave both where they are and you stay on budget.
- Material grade: Acrylic versus tile versus solid-surface accounts for most of the spread.
- Permit scope: A pan and valve change can require a permit and inspection; cosmetic-only swaps may not. We tell you which side your job falls on before anything gets ordered.
A written estimate from Groundwork is a line-item quote: demo, rough-in, waterproofing, tile or panel, fixtures, permit fees, and haul-away, each with a price. What usually stays outside it: repairing hidden framing or plumbing that only shows up after demo, and any change you make after materials are ordered. We price those in writing before doing the work.
See the difference
Before
After
Before
After
Before
AfterWhat Gardena’s Housing Stock Does to This Job
Gardena is built on post-WWII 1950s and 60s single-story stucco tract homes on tight lots, many still on original slab foundations with galvanized or early copper plumbing. That matters here: when we open the wall behind a tub in a house off Western Avenue or near Rowley Park, we frequently find a valve that’s reached the end of its life and a drain connection that needs updating, not just a cosmetic swap. Doing that work during the conversion costs far less than doing it twice.
The other local reality is the building department. This city’s plan check has a reputation for being thorough, so we submit complete drawings with the pan and valve details up front instead of getting sent back with comments. Because parcels are small and homes sit close together, we keep the work zone tight and haul debris out the same day it comes down. Gardena’s marine layer and low rainfall mean we don’t fight moisture from outside, but the sandy coastal soils and high water table in some areas make us look hard at the slab around the drain before we set a pan. Dry Santa Ana wind days can also restrict outdoor hot work, which rarely touches an indoor conversion but does affect any cutting or solvent work that needs to happen outside.
Serving Gardena, CA – Our Local Coverage Area
We serve Gardena and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Tub-to-Shower Conversion in Gardena

Most conversions take 5 to 10 working days from demo to final walkthrough. A simple acrylic unit can finish in the shorter end; tiled walls with a glass door and a permit inspection run toward the longer end. Call (888) 345-8164 for a timeline on your layout.
Usually yes, if the drain or valve is changing. A pan and valve replacement is plumbing work, and the city’s building department will want to inspect the waterproofing and rough-in before the finish goes on. We handle the submittal and schedule the inspections. Call us and we’ll tell you where your project lands.
Sometimes. If the existing drain happens to line up with the new pan’s location, and the valve stays on the same wall, you’re looking at a lower-cost job. In most cases the tub drain does need to shift, which is a slab or subfloor cut. We know which one you have after the first visit.
Between $3,500 and $10,000 for a typical alcove. The low end is an acrylic pan and surround with minor rough-in; the high end is tile, frameless glass, a new valve, and some repair work. Call (888) 345-8164 for a written line-item quote at no charge.
Waterproofing and workmanship are covered by our 730-Day Done Right Promise. If something we installed fails within that window, we make it right. Product warranties come from the manufacturer on top of that. Call (888) 345-8164 to ask about coverage for your specific build.
Get a Free Estimate for Your Gardena Conversion
We’ll come out, measure your alcove, look behind the wall, and hand you a written line-item quote for your tub-to-shower conversion in Gardena. That covers demo, rough-in, waterproofing, finish, and permit fees, with the $1,000 off projects over $10,000 promotion applied if you qualify, and 0% financing for 18 months if you want to spread the cost. Call (888) 345-8164. A live person answers.
Written by the team at Groundwork Construction Co.












