







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Lomita, CA: What the Job Actually Takes
A chain link fence in Lomita runs $3,500 – $9,000 for a typical residential install, and most jobs are finished in one to three days once the posts are set. You’re getting galvanized steel posts, top rail, tension wire, and mesh stretched drum-tight between terminal posts, all sized to your lot lines. Call (888) 345-8164 for a free on-site estimate and a written, line-item quote before anything gets dug in.
How We Build a Chain Link Fence Here, Stage by Stage

The sequence matters more than most homeowners expect, because how the posts go in determines whether the fence is still straight in ten years. Here’s the real order of events.
Stage 1 – Site visit and line check (day 1, about an hour). We walk the property with you, confirm where the fence should run, and check for the things that quietly drive cost: the block wall you’re tying into, the property-line survey, and any buried irrigation, gas, or electrical runs. You decide the height, the gate locations, and whether you want the line flush with a neighbor’s existing fence or offset a few inches inside your lot.
Stage 2 – Utility locates and layout (day 1, same visit). Before a shovel moves, locates get called in and the fence line gets marked. On the small infill lots around Lomita, that spacing between your fence and a neighbor’s is tight, so we lay out the terminal posts and corners first. You confirm the gate swings.
Stage 3 – Digging and setting posts (day 1 into day 2). Terminal posts and corners get dug to depth and set in concrete, typically 2 to 3 feet down depending on the post size and how much the soil holds. Line posts follow at 8- or 10-foot spacing. Concrete needs roughly a day to cure before you tension anything, which is why this isn’t a same-afternoon project. This is the stage that decides whether the fence sags later, and it’s the one we don’t rush.
Stage 4 – Rails, mesh, and tension (day 2 into day 3). Top rail goes on, tension wire runs the bottom, and the mesh gets stretched and fastened. Gates get hung, aligned, and tested. Stretch tension is the difference between a fence that rings tight when you tap it and one that waves in a wind off the coast.
Stage 5 – Walkthrough and cleanup (end of day 3). We walk the whole run with you, check gate clearance, pull leftover concrete and wire, and hand over the written workmanship coverage. Most single-run residential jobs land inside three working days start to finish.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Chain Link Fence Choices You’ll Actually Make
- Galvanized vs. vinyl-coated mesh. Bare galvanized is the lower-cost standard and holds up well in dry South Bay air, but salt-laden coastal fog slowly dulls it. Color-coated (black or green bonded vinyl over galvanized core) costs more up front and resists that corrosion far better here. On a Lomita lot where the fence will be seen from the street, coated reads as intentional rather than industrial.
- Post gauge and diameter. Lighter 1-5/8″ posts suit a short residential run. Heavier 2-3/8″ line posts with thicker walls cost more but hold a taller fence, a longer span, or a gate without leaning. If your fence line backs onto open ground or a corner lot takes the wind, this is where the money goes.
- Height and top rail. Four feet is the residential default; five and six feet give more security and change the pricing. A top rail plus tension wire gives the tightest, straightest look; tension wire alone is a bit less expensive and less rigid.
- Gate style. Walk gates and drive gates are the pieces that fail first, so we spec heavier frames and proper hinges on anything that gets used daily. Decide now whether you want one drive gate or two swinging leaves.
- Tie-ins. If the fence meets an existing block wall or a neighbor’s fence, the terminal and brace at that junction need to be planned, not improvised.
What a Chain Link Fence Costs in Lomita, CA

Residential chain link fence installation in Lomita typically falls between $3,500 and $9,000. The low end is a straight run of standard galvanized fence at four feet on flat, clear ground. The high end is a longer perimeter, coated mesh, heavier posts, two or more gates, and line that has to work around a block wall, a slope, or a tight lot line.
What pushes the number up or down:
- Linear feet and configuration. Perimeter length is the biggest lever, and corners and terminals cost more per foot than straight line because of the bracing and extra concrete.
- Post size and gauge. Heavier posts and thicker walls raise material cost but cut future repairs.
- Mesh coating. Bonded vinyl over galvanized adds cost and buys corrosion resistance that matters in coastal air.
- Existing conditions. Removing an old fence, cutting through concrete or a paved strip for posts, or tying into masonry all add labor.
- Gates. Each gate is its own line item, and drive gates weight the frame and hinges.
A written estimate from us lists the linear footage, post size and spacing, mesh type, gate count, removal, and whether permits apply, so the price you see is the price you pay. What it typically doesn’t include: utility relocation, which is a separate trade if a line has to move, and fence staining or landscaping restoration unless you ask for it up front. If the project is part of a full Fence Installation in Lomita plan that includes a front-section upgrade, we scope both together so the lines match.
See the difference
Before
After
Before
After
Before
AfterWhat Lomita Lots Do to a Chain Link Fence Job
Lomita is a fully built-out Harbor Gateway city of roughly one square mile, surrounded by Torrance and with no open land left to develop. That changes fence work here: nearly every job is a replacement or a run dropped onto an existing tight infill lot rather than a fresh subdivision layout. Because the City of Lomita runs its own small plan-check process on top of LA County’s coastal-area rules, permits, setbacks, and property-line questions get settled lot by lot here in a way they don’t on the open ground in neighboring Torrance or unincorporated county land. The housing stock is mostly 1920s to 1950s bungalows on 5,000 to 6,000 square foot lots, so old block walls, mature hedges, and buried irrigation along the PCH and Lomita Boulevard corridors are the norm, and post placement has to work around them. The marine layer and salt air also drive what we see fail: corroded fasteners, pitted galvanized mesh, and posts rusting at the concrete line. We spec coated mesh and heavier hardware on coastal-facing lines for exactly that reason. If the same project brings up driveway work at the gate opening, homeowners often pair this with Concrete Driveways & Concrete Work in Lomita so the apron, posts, and gate all get poured and set in one pass.
Serving Lomita, CA – Our Local Coverage Area
We serve Lomita and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Chain Link Fence in Lomita

A typical residential chain link fence in Lomita takes one to three working days, with the concrete post footings needing about a day to cure between setting and tensioning. Longer perimeters, multiple gates, removal of an old fence, or cutting through concrete push the job toward the three-day mark. Call (888) 345-8164 for a timeline specific to your lot.
Chain link fences in Lomita often fall under the city’s fence-height rules and don’t always require a permit, but it depends on height, location on the lot, and whether a corner sight line is involved, so we check the City of Lomita’s own building department rather than assume. We’ll tell you straight whether your run needs a permit and pull it if it does. Call (888) 345-8164 to get the answer for your address.
No, the written line-item estimate is what you pay, and we don’t issue change orders for surprises we should have caught on the walkthrough. The only things that shift the number are changes you request, like adding a gate. Call (888) 345-8164 for a fixed quote.
Yes, in most cases we lay out the run and call in utility locates before digging, then route posts around irrigation, gas, and electrical runs on your lot. If a line sits directly where a post has to go, that becomes a clear discussion up front, not a surprise mid-dig. Call (888) 345-8164 and we’ll walk your property first.
Our fence work is backed by our written workmanship commitment, and installing this as part of our Fence Installation service carries the same coverage. Material warranties follow the manufacturer’s terms on the mesh and hardware. Call (888) 345-8164 and we’ll put the warranty in writing with your estimate.
Get Your Chain Link Fence Estimate in Lomita
If you’re in Lomita and ready for a straight answer on your chain link fence, call (888) 345-8164 to schedule a free on-site estimate. A live person answers day or night, we walk the property with you and measure the actual run, and you leave with a written line-item quote showing footage, post spec, mesh type, and gate count. No pressure, no vague numbers. Estimates are free, and qualifying projects over $10,000 get $1,000 off with 0% financing for 18 months available.
Written by the team at Groundwork Construction Co.












