







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Compton, CA: What the Job Actually Looks Like
An iron fence in Compton runs $3,500 – $9,000 installed, with most residential jobs landing in the $4,500 – $7,000 range for 100 to 150 linear feet of painted steel or wrought iron on a standard R-1 lot. The work itself takes two to four days once fabrication is finished, and permits usually add one to three weeks to the front end. Call (888) 345-8164 and we’ll walk your property, check your setbacks, and put a written number in your hand.
How We Build an Iron Fence in Compton, Start to Finish

Iron work is fabrication-heavy, so the schedule splits cleanly between the shop and the yard. Here’s the real sequence.
Stage 1: Site visit and measurement (day 1, about 90 minutes)
We walk the property line with you, confirm where the fence actually goes, and measure the run. On Compton’s small lots this is where the real decisions happen, because your side-yard setbacks are tight and a fence set two inches off the line can create a dispute with a neighbor. You decide the height, the run, and whether the fence closes a driveway or leaves a gate. We also check for buried irrigation, gas stub-outs, and the meter locations near your property edge.
Stage 2: Permit and utility check (week 1 – 3)
We file with the City of Compton and pull the applicable permits for fences over the standard height threshold and for any fence in a front-yard setback. We call 811 so utilities get marked before anyone digs. This is the waiting stage, and it’s where homeowners who shop on price alone get burned, because a fence contractor working without a permit puts the risk on you at resale. We handle the filing and the inspection scheduling.
Stage 3: Layout, demo, and post setting (day 1 on site)
We string the line, dig the post holes, and set the posts in concrete. For a 120-foot run with posts every 6 to 8 feet, expect one long day. If there’s an old fence to remove, add four to six hours. Posts cure overnight, which is why we never hang panels the same day.
Stage 4: Panel and gate install (day 2 – 3)
Panels get hung, leveled, and welded or bracketed to the posts. Gates get their hinges, latches, and any self-closing hardware. You decide the gate swing direction and latch style before this day, because changing it later means re-welding.
Stage 5: Finish, touch-up, and final walk (day 3 – 4)
We touch up weld burns and scratches with matching paint, confirm every gate swings clean, and walk the line with you. You get the warranty paperwork at the walk-through, and we don’t call the job done until you’ve signed off on it. If something isn’t right, our 730-Day Done Right Promise covers it: we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between on a Compton Iron Fence
Iron isn’t one product. The choices below are the ones that actually change how your fence looks and how long it lasts.
- Painted steel vs. true wrought iron. Painted steel tube is the workhorse. It’s lighter, cheaper, and takes paint well, and it handles Compton’s sun and dry air fine. True wrought iron is heavier and more expensive, but it holds detail and resists impact better on a busy frontage.
- Powder coat vs. field paint. Factory powder coat holds color for years and resists chipping. Field-painted iron costs less up front and needs a repaint every four to six years in this climate.
- Pickets vs. flat-bar panels. Pickets give you the classic look and better visibility. Flat-bar panels are cleaner, more modern, and easier to keep clean along a driveway edge.
- Height. A 4-foot fence handles a garden boundary. A 5- to 6-foot fence handles security along a frontage or an alley-facing side yard, which matters on Compton’s through-block lots.
- Gate hardware. Manual latch, self-closing hinge, or a keyed lock. If you want a rolling-code keypad, plan for it now, because the wiring has to go in before the post is set.
- Finial and rail detail. Spear-top finials and double rails cost more per panel, and they’re the first thing people notice from the street.
What an Iron Fence Costs in Compton, CA

Plan on $3,500 – $9,000 for a residential iron fence in Compton, with the $4,500 – $7,000 band covering most of the work we do. The number moves on these five things:
- Linear footage. This is the biggest driver. A 60-foot side-yard run sits near the bottom of the range; a 200-foot perimeter with a driveway gate pushes the top.
- Height and gauge. Stepping from 4-foot to 6-foot pickets, or moving to a heavier wall thickness, adds real steel cost, not just labor.
- Gates. A single walk gate adds $600 – $1,500. A double driveway gate with keyed hardware can add $1,800 – $4,000.
- Site conditions. Sloped grade, old concrete to break out, or roots in the post line all add hours.
- Finish. Powder coat adds cost up front and saves you repainting down the line. Field paint trades that savings for maintenance.
Our written estimate breaks out posts, panels, gates, concrete, finish, and permits as separate lines, and the number you sign is the number you pay. No change orders for work we should have scoped. If the job runs over $10,000 (usually a large perimeter with gates and a keypad), the $1,000 off projects over $10,000 promotion applies, and 0% financing for 18 months is available if you’d rather spread it out.
The estimate covers fabrication, delivery, install, concrete, and cleanup. It does not cover old fence demolition unless you ask for it, and it doesn’t cover the permit fee for the City of Compton filing, which we pass through at cost rather than marking up.
See the difference
Before
After
Before
After
Before
AfterWhat Compton Homes Specifically Do to This Job
Most of the homes we build iron fence on in Compton are 1940s – 1960s single-story stucco tract houses on small R-1 lots, and that changes the job in ways it doesn’t in the newer subdivisions up north. The side-yard clearances in the 90220 and 90222 core are narrow, often under four feet, so post placement has to respect the setback line to the inch. We survey the line before we dig. Alley-facing properties in 90221 frequently need an iron gate on the alley side for security, which means a heavier post set and keyed hardware rather than a garden latch.
Two local conditions matter for the finish. Compton sits in the Santa Ana wind corridor, so gates need stiffer hinges and posts need deeper concrete than a sheltered yard would get. And the intense summer sun will chalk a cheap field paint in two seasons, which is why we default to powder coat on sun-exposed runs. If you’re redoing the side yard at the same time, homeowners often pair this with Patios, Walkways & Pool Decks in Compton so the concrete apron and the gate post get poured together.
If the iron fence is part of a larger site plan, say a rear yard with an ADU, we’d fold it into the scope. Homeowners often pair this with ADU Design & Permitting in Compton so setbacks and the fence line are resolved in one permit package instead of two. And if you’re replacing the boundary while redoing the driveway or entry, it reads as one project: see our Fence Installation service for how we scope the full perimeter. For the broader picture across the Compton area, or to fold this into a Fence Installation in Compton plan that includes matching materials and a single install window, call us and we’ll map it out.
Serving Compton, CA – Our Local Coverage Area
We serve Compton and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Iron Fence in Compton

Two to four days on site once fabrication is done, plus one to three weeks for permits on the front end. The install itself is fast because the panels arrive pre-built. The wait is the shop and the City of Compton filing. Call (888) 345-8164 and we’ll give you a real date, not a vague window.
Yes for most front-yard and over-height fences, and no for a standard rear or side-yard fence at or under the height limit. The line is set by the City of Compton zoning code, and we check your specific lot and setback before we file. If a permit is needed, we pull it and handle the inspection.
No. Iron fence posts go in the yard, not into the house, so the job doesn’t touch plumbing, wiring, or framing. The only thing we ever need to move is irrigation or a gas stub near the property line, and we flag that at the site visit before anyone digs.
Most jobs fall between $3,500 and $9,000, with the typical residential run landing at $4,500 – $7,000. Footage, height, gate count, and finish drive the number. Call (888) 345-8164 for a free on-site estimate with a line-item quote.
Every install is covered by our 730-Day Done Right Promise, which means if something isn’t right, we come back and fix it. That covers the installation and workmanship for two years. Call (888) 345-8164 and we’ll go over exactly what’s covered in writing.
Get a Free Iron Fence Estimate in Compton
Call (888) 345-8164 to schedule a free on-site estimate for your iron fence in Compton. We’ll measure the run, check where your property line and setbacks actually fall, and give you a written line-item quote the same visit, with the permit and inspection steps spelled out. A live person answers, day or night. No pressure on the call, just a real number to plan around.
Written by the team at Groundwork Construction Co.












