







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in Signal Hill, CA: What It Costs and How It Goes
A new concrete driveway in Signal Hill typically runs $4,500 – $12,000, and most residential pours take three to five working days from demo to the day you can park on it. A full replacement lands at $5,000 – $14,000 once you factor in hauling off the old slab and re-grading on a hillside lot. The number that actually matters is your finished price. Call (888) 345-8164 and we’ll put it in writing after we walk the property.
How a concrete driveway actually gets built here

Concrete work is unforgiving about sequence. Skip a step and you’ll see the evidence in two winters. Here’s the order we work in on Signal Hill jobs, and where your decisions land.
Day 1: site visit and utility locate. Before anything gets cut, we call in the 811 locate and, on this hill, walk the dig footprint against any known legacy oil infrastructure. On older Signal Hill properties we also check for undocumented flatwork, old patio slabs poured over soil, and drainage that runs toward the house instead of away. This is the stage where you decide the driveway width and whether you want a widened apron for a second vehicle. Add a day if there’s any question about what’s buried.
Day 1 – 2: demolition and haul-off. We break out the existing slab with a skid-steer or demo hammer, load it, and haul it. A standard two-car driveway is roughly 10 to 12 cubic yards of debris. Tight lots and hillside grade slow this down because the truck can’t always get close. On steep Signal Hill streets we may need to stage material at the street and carry it up, which is a line item you’ll see on the estimate.
Day 2 – 3: subgrade prep and formwork. Exposed subgrade is compacted in lifts with a plate compactor. That’s where most cheap driveways fail, and it’s the part nobody photographs. We verify slope for drainage (typically a 1% to 2% fall away from the structure), then set forms and steel. You confirm the finish and joint layout before we pour, because after that it’s committed.
Day 3 – 4: pour, screed, finish. A typical residential pour here is 4 to 6 inches thick, with 5 inches or more where a heavier vehicle parks. Control joints get cut or tooled so cracks land where you won’t see them. Finish is broom, exposed aggregate, or a light stamp. The crew is background-checked and uniformed, and the pour usually wraps in a single day.
Day 4 – 7 and after: curing and joint sealing. Concrete hits usable strength in about seven days for foot traffic and longer for vehicles, so we keep weight off it until it’s ready. Curing in dry coastal heat matters more than people expect; we keep the surface damp or use a curing compound so it doesn’t dry too fast and dust. Final walkthrough is where you confirm joints, drainage and finish, all covered under our 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between
- Standard broom-finished concrete. The workhorse for Signal Hill driveways. Grippy, low-maintenance, and the most cost-effective at the low end of our $4,500 – $12,000 range. Trade-off: plain, and it will show hairline cracks eventually.
- Exposed aggregate. The top layer of paste is washed away to reveal the stone underneath, giving texture and a bit of visual interest. Costs more than broom finish and holds up well to sun and rain. Suits hillside homes where the driveway is visible from the street.
- Stamped or patterned concrete. Pressed to mimic stone or pavers, and it reads as something more than gray slab. Higher cost and a bit more upkeep. Worth knowing that our related Driveway & Pavers in Signal Hill page covers the paver route if that pattern is really what you’re after.
- Thickness and steel. Standard residential is 4 inches; we recommend 5 inches and rebar for driveways carrying heavier vehicles or on unstable fill. This is the single biggest quality lever, and it costs a modest amount more up front.
- Drainage: swales, channel drains, and slope. On hillside lots, water management is part of the pour. A channel drain or a graded swale keeps runoff off the slab and away from the foundation.
- Color and integral pigment. If you want a tone other than gray, integral color goes in the mix rather than on top, so it won’t wear off.
What concrete driveways & concrete work costs in Signal Hill, CA

Concrete driveway installation in Signal Hill runs $4,500 – $12,000 for a standard residential pour, and a full replacement with demo and haul-off is $5,000 – $14,000. Those are real numbers for this market, and we hold to them: the price in your written estimate is the price you pay.
What pushes a job toward the high end:
- Size. Square footage drives the concrete, steel and labor. A long, narrow hillside driveway costs more per foot than a wide one because of access and forming.
- Existing condition and demo. Thick or reinforced slabs, or flatwork poured over another slab, add demolition hours and haul-off weight.
- Grading and slope. A steep lot means cut and fill, retaining considerations, and often extra base material. This is the single most common reason Signal Hill driveways cost more than a flat-lot job.
- Finish grade. Broom is the baseline; exposed aggregate and stamped work raise the line item.
- Permits and inspection. Grading and drainage work near the structure can pull in city review. Some jobs don’t need a concrete permit; hillside cuts and retaining walls often do.
A written estimate from us includes demo, haul-off, subgrade prep, compaction, forms, steel, the pour, finish, joint cutting, the curing method, and final cleanup. It does not include structural repairs found under the old slab, gas or water line relocation if a line is in the way, or landscaping repair around the edges. Those get quoted separately before anyone touches them, never buried in the bill.
See the difference
Before
After
Before
After
Before
AfterWhat Signal Hill homes specifically do to this job
Signal Hill is a small, fully built-out city wrapped entirely inside Long Beach, sitting on top of the original Signal Hill oil field. That single fact shapes nearly every concrete pour here. There’s no greenfield land, so almost every driveway job is a rebuild on a tight infill lot or a hillside grade. Our crews regularly hit abandoned oil well casings, old pipelines, and buried derrick pads during excavation. When that happens, we stop, document, and coordinate with the city; it’s not a scare story, it’s just the reality of digging on this hill, and it’s why a skid-steer operator who’s worked Signal Hill streets matters.
The housing stock makes it worse. Most properties are mid-century tract homes from the 1940s through the 1960s, and many carry non-permitted past flatwork or additions poured right over the old grade. On hillside view lots and slopes, winter rain turns erosion and slope stability into a recurring concern, so drainage, retaining walls, and grading review come up on jobs where a flat-lot city would just pour and move on. We see failed aprons and cracked slabs all along the residential streets here, and we build every pour to stand up to that, with a drainage plan in the estimate.
Homeowners often pair a new driveway with a separate project while the equipment and crew are already on site, and it can make sense to sequence the work. If you’re planning something bigger, that’s a different scope; our Signal Hill service page shows everything we build here, and when the project involves converting an existing structure, Garage Conversion ADU in Signal Hill and New Detached ADU in Signal Hill are common add-ons. Our broader Driveway & Pavers service covers the paving side if you’re comparing concrete against pavers.
Serving Signal Hill, CA – Our Local Coverage Area
We serve Signal Hill and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – concrete driveways & concrete work in Signal Hill

Expect three to five working days from demo to a poured, finished slab, plus about a week before you drive on it. Hillside access and utility issues can stretch the demo stage by a day or two. Call (888) 345-8164 to schedule a free on-site estimate with a real timeline for your lot.
Often not for a same-footprint replacement, but grading, drainage, and retaining work near the structure typically do trigger city review. Given the oil-field history here, we check the dig footprint and review requirements before the estimate is final. Call (888) 345-8164 and we’ll tell you what your specific job needs.
Standard installation is $4,500 – $12,000, and a full replacement runs $5,000 – $14,000 depending on size, slope and finish. Call (888) 345-8164 for an exact quote; estimates are free and itemized line by line.
No, not for the scope we’ve quoted. Our upfront pricing means the number in your written estimate is what you pay. If we uncover a buried line, an old oil casing, or rotted subgrade, we stop and quote that separately before doing anything, with 0% financing for 18 months available on larger projects.
Every pour is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction. If the finish, drainage or joints aren’t right, we make it right. Call (888) 345-8164 with any question.
Get a free estimate for concrete driveways & concrete work in Signal Hill
Call (888) 345-8164 to schedule your free on-site estimate. A live person answers around the clock, and on the call we’ll get your address, talk through the driveway and what’s under it, and set a visit. You’ll get a written, itemized quote for concrete driveways & concrete work in Signal Hill with no surprise line items, and we stand behind it with our 730-Day Done Right Promise. Built to last, backed in writing.
Written by the team at Groundwork Construction Co.












