







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Signal Hill, CA: What It Costs and How Long It Takes
A tub-to-shower conversion in Signal Hill typically runs $3,500 to $10,000 and takes 5 to 10 working days from demo to final inspection, depending on whether the drain stays put and what’s behind the tile. Most conversions land near $6,000: a standard 30×60 alcove, a pre-sloped pan, porcelain or acrylic walls, and a new valve. Call (888) 345-8164 for a free on-site estimate and a line-item written quote before any work starts.
How We Run a Tub-to-Shower Conversion, Stage by Stage

A conversion is smaller than a full bathroom remodel, but the sequence matters more than the square footage. Here’s the actual order we work in, and what you decide at each point.
Stage 1: Tear-out and inspection (day 1)
We pull the tub, the surround, and the valve trim. Then we open the wall behind the wet wall to look at the drain, the p-trap, and the framing. On a 1950s Signal Hill house this is where we find things: cracked cast iron, a drain that was never re-supported, or studs that swelled from a slow leak behind the old tub. You don’t decide anything yet. We photograph what we find and send it to you the same day, with a price for any repair that wasn’t in the original scope. Upfront pricing, no surprises.
Stage 2: Plumbing rough-in and permit inspection (days 2-3)
If the drain stays in roughly the same spot, this stage is short. If you’re moving the drain to a linear or center location, the floor gets opened and the trap gets re-cut. The pressure-balancing valve gets replaced at minimum, and a thermostatic valve is worth the upgrade if you’ve ever been scalded by a toilet flush. The rough plumbing gets inspected before anything closes up. You’ll choose your valve trim and showerhead brand here, and this is the last easy moment to add body sprays or a hand-held on a slide bar.
Stage 3: Pan, waterproofing, and backer (days 3-5)
This is the stage that decides whether the job lasts 15 years or 5. We build a sloped mortar pan or set a manufactured pan, then waterproof with a bonded membrane or a liquid-applied system, and run it up the walls past the showerhead. A flood test holds water in the pan overnight and gets documented before tile goes down. You choose wall substrate here: cement board or a foam board system. We won’t set tile on drywall in a wet zone; that shortcut is the single most common reason shower tile fails in this climate.
Stage 4: Tile, fixtures, and glass (days 5-9)
Tile sets over two to three days depending on pattern and format. Grout and sealant come next, then the valve trim, showerhead, drain grate, and any built-in niche or bench. Glass gets templated after tile is complete and installed a few days later, so a frameless enclosure can add a short gap in the schedule. You’ll pick a grout color here, and this is the point to confirm you want a curb or a curbless entry; curbless needs to be planned at Stage 3, not now.
Stage 5: Final inspection and walkthrough (day 9-10)
The city inspects the finished plumbing and, where required, the waterproofing. We walk the job with you, run the shower, check the drain slope and the door swing, and hand over care instructions for the stone or tile you chose. Every tub-to-shower conversion we do is backed by our 730-Day Done Right Promise, so if something isn’t right, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Actually Make Between
Most of the price spread on a tub-to-shower conversion in Signal Hill comes down to four decisions. Here’s the honest trade-off on each.
- Pan type: A manufactured acrylic pan is the cheapest and fastest, pre-sloped and leak-resistant out of the box. A tiled mortar pan with a linear drain looks better and lets you go curbless, but adds $1,200 to $2,500 in labor and waterproofing. Foam-board pan kits sit in between.
- Wall material: Acrylic surrounds are the low-maintenance pick, install in a day, and cost $800 to $2,000 for materials. Porcelain or ceramic tile costs more up front and needs sealing on natural stone, but holds resale value and lets you match the rest of the bathroom.
- Valve and trim: A basic pressure-balance valve runs a few hundred dollars installed. A thermostatic valve with a separate volume control can add $800 or more, but ends the cold-shock problem in a shared bathroom.
- Glass: A framed sem-frameless door is the budget option. A frameless 3/8-inch enclosure is the upgrade most buyers pick, and it’s also the piece that gets templated last, so it can stretch the schedule. Kohler trim and tile from a reputable line hold up well here.
- Bench and niche: A corner bench and a recessed niche add usable storage and cost $300 to $900 together. Worth it in a shared shower. Not worth it in a small hall bath where the space is tight.
What Tub-to-Shower Conversion Costs in Signal Hill, CA

Expect $3,500 to $10,000 for the conversion itself. A straight swap in a standard alcove with the drain in place and builder-grade materials sits at the bottom of that range. Moving the drain, going curbless, adding a bench, or upgrading to frameless glass and large-format porcelain pushes you toward $10,000. Here’s where the money actually goes:
- Demo and haul-away: $300 to $700
- Plumbing rough-in and valve: $500 to $1,800
- Waterproofing and pan: $700 to $2,200
- Tile and setting materials: $1,000 to $3,500
- Glass enclosure: $600 to $2,000
- Permit and inspection fees: typically a few hundred dollars, billed at cost
Five things move the number: whether the drain stays put, whether we open the floor for a curbless entry, the condition of the framing and old plumbing behind the wall, the grade of tile and fixture you choose, and whether the permit requires a waterproofing inspection. Our written estimate lists every line and what’s included and excluded, so nothing shows up as a change order later. The number you see is the number you pay. If you’re rolling this into a larger project, our Bathroom Remodeling in Signal Hill page covers the wider scope.
See the difference
Before
After
Before
After
Before
AfterWhat Signal Hill Homes Do to This Job
Signal Hill is a fully built-out city wrapped inside Long Beach, and most of the housing stock is mid-century single-family on hillside and view lots, with newer infill condos and townhomes along the lower edges near Long Beach. That matters for a tub-to-shower conversion because older homes here often carry outdated plumbing, cast iron or galvanized drains, and non-permitted past additions. When we open the wet wall near the hilltop streets or on the slopes above 90755, we’re prepared to find a prior remodel that wasn’t inspected. The bigger local wrinkle is below grade: contractors digging on Signal Hill routinely hit old oil well casings, pipelines, and buried derrick foundations from the hill’s oil-boom era, and any excavation on these lots can trigger well-abandonment records and extra city scrutiny that surrounding Long Beach projects never see. A conversion rarely digs deep, but if we need to open the slab for a relocated drain, we budget time to check records before the saw comes out. Permits we pull are pulled in the city’s name and inspected, and the steep oil-scarred slopes up here also mean we watch for slope and drainage issues when a bathroom sits against an exterior hillside wall.
Serving Signal Hill, CA – Our Local Coverage Area
We serve Signal Hill and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Tub-to-Shower Conversion in Signal Hill

Most conversions take 5 to 10 working days from demo to final walkthrough. A straight swap with the drain in place runs closer to 5 days. Moving the drain, going curbless, or waiting on a templated frameless enclosure stretches it to 10. Call (888) 345-8164 for a schedule estimate once we’ve seen the bathroom.
Yes, in almost every case. Replacing a tub with a shower involves plumbing changes and often a new valve, and the city inspects that work. We pull the permit, meet the inspector, and give you the signed-off record. Skipping the permit is the fastest way to create a headache at resale.
Yes, and that’s the most common and affordable path. If the drain stays in roughly the same location and the rough framing is sound, we convert the alcove without opening the floor or moving walls. If you want a linear drain or curbless entry, that changes the scope and the price.
It runs $3,500 to $10,000, with most jobs landing around $6,000. Drain relocation, curbless entry, frameless glass, and tile grade are the main price drivers. Call (888) 345-8164 for a written line-item quote; estimates are free and no-hassle.
Every tub-to-shower conversion is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space, and it’s in writing. Call (888) 345-8164 with any warranty question before you book.
Get a Free Tub-to-Shower Conversion Estimate in Signal Hill
Call (888) 345-8164 to schedule a free on-site estimate for your tub-to-shower conversion in Signal Hill. We’ll measure the alcove, check the drain and valve, and give you a written line-item quote with the scope spelled out, so you know the price before we pick up a tool. If a full redesign makes more sense, our bathroom remodeling service covers the broader work, and we serve the whole of Signal Hill. Homeowners often pair this with Metal Roofing in Signal Hill or Tile Roofing in Signal Hill while we’re on site. Live person, 24/7, every call.
Written by the team at Groundwork Construction Co.












